How do my inards look? - page 2 - General - VWDiesel.net The IDI, TDI, and mTDI source.

• #15 by zukgod1 on 08 Oct, 2008 15:48
• Quote from: "Trev0rbr"

  my suggestion:
  
  
  2.add semen
  

  
  
  
  
  Wait... What??   :?
• #16 by jimfoo on 08 Oct, 2008 15:55
• Maybe it gives your tranny new life. :lol:  :lol:  :lol:
  I think he has been looking at too much porn. :lol:
• #17 by burn_your_money on 08 Oct, 2008 17:29
• Well I have most of those steps covered, not all though :?  :lol:
  
  Hopefully step 5 will be soon
• #18 by fdnyguy on 08 Oct, 2008 18:19
• Quote from: "zukgod1"

  Quote from: "Trev0rbr"

  my suggestion:
  
  
  2.add semen
  

  
  
  
  
  Wait... What??   :?

  
  
  Would this be for coming and not going?
• #19 by Turbinepowered on 09 Oct, 2008 03:04
• Quote from: "Trev0rbr"

  my suggestion:
  
  2.add semen
  
  5.drive and enjoy

  
  
  
  Wroooooooooooong kind of tranny there, bud!  
• #20 by burn_your_money on 19 Oct, 2008 14:25
• Well it turns out I'm a genious idiot. I *thought* the tranny was siezed so I ordered up a rebuild kit and started studying my bentley. Once I put the tranny up on the table I knew that it wasn't siezed and the piece I was trying to turn isn't suppose to turn but I figured I was this far, why not go all the way.
  
  Pictures showing my stupidity below
  
  
  
  
  
  
  
  
  
  
  
  
• #21 by burn_your_money on 19 Oct, 2008 14:27
• 
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  Hopefully it works when it comes time to install it :roll:
• #22 by Smokey Eddy on 19 Oct, 2008 14:56
• What on earth is the second last picture of?
  I dont know autos at all and that picture looks like a brain or something.
  
  Also,
  

  Quote

  Well I have most of those steps covered, not all though  
  
  Hopefully step 5 will be soon

  
  
  Was step 2 kinda awkward with Giles around or did you not do this in Giles' surgically clean injection shop. I wouldn't bring a Tranny in there either.
• #23 by burn_your_money on 19 Oct, 2008 16:09
• That's the valve body. New trannys use electric solenoids to control the tranny, these old ones use hydraulic pressure. I have no idea what goes on in that contraption. I just cleaned it and put it back together.
  
  I did it in the shop. There were no pumps around or anything. Some of the pumps we get are way filthier then that transmission so it really isn't much different. You just have to clean up afterwards so the bench still sparkles.
  
  Step 2 will occur if the thing works afterwards :lol:
• #24 by Slave2School on 20 Oct, 2008 20:36
• While you have it there contact peloquin and see if you can even maybe use the 80% kit they have or the real meal deal
• #25 by burn_your_money on 21 Oct, 2008 07:09
• You must think I have money  :lol:
  
  The nice thing about the auto is you don't need to take the diff or final drive apart, it's completely seperate
• #26 by zukgod1 on 21 Oct, 2008 07:36
• Whats the final drive on that trans Tyler?
• #27 by burn_your_money on 21 Oct, 2008 09:35
• Do you mean the ratio?
• #28 by zukgod1 on 21 Oct, 2008 09:53
• Ya. R&P and final gear..
  
  Or just what will mph it be spinning at when the engine is @ 3K?
• #29 by burn_your_money on 21 Oct, 2008 16:54
• I'm not sure. Somewhere around 3000 - 3500 at 60 mph/100kmh from what I've read