« previous next »
Pages: [1]

Author Topic: removing vacuum pump  (Read 3705 times)

August 09, 2011, 04:17:12 pm

92EcoDiesel Jetta

  • Guest
removing vacuum pump
« on: August 09, 2011, 04:17:12 pm »
After a head gasket job, should I pull the vacuum pump so I can manually spin the oil pump to get oil circulated through the engine before starting it? I undid the 13 mm bolt and clamp but the vacumm pump seems to be stuck in there pretty good due to corrosion. Should I put a slide hammer on it and tap it out?
Logged
Reply #1August 09, 2011, 04:38:47 pm

the caveman

  • Veteran
  • Offline
  • ***
  • 1739
Re: removing vacuum pump
« Reply #1 on: August 09, 2011, 04:38:47 pm »
With just a head gasket done, there should be no issue about oil . To be sure pour a bunch all over the cam and lifters. It's not your breaking in a rebuilt engine.. More important is to make sure you bleed all the air out of the cooling system once it's running
Logged
" I'm a vegetarian,not because i love animals, it's because i hate plants"
1970 Type 3 fastback
1972 Renault 12
1971 Super Beetle 140 HP 159 ft lbs
1987 Fox
1989 TD Jetta
1990 Fox
1989 Fox
1998 TDI Jetta
1990 T3 German MIL Transporter 1.9 na Giles super pump
1997 Jetta GLX TDI
Reply #2August 09, 2011, 05:57:27 pm

theman53

  • Global Moderator
  • Veteran
  • Offline
  • ***
  • 7835
  • Personal Text
    Holmes County Ohio - North Central Ohio
Re: removing vacuum pump
« Reply #2 on: August 09, 2011, 05:57:27 pm »
^ good advice.
I still like seeing the oil up top. You never know when brain fade sets in and you put the top or OBEN side down and no oil comes up. I haven't done it yet, but I am sure I will sometime.
The vac pump should come out if you have that clamp off and twist it with a pipe wrench. Be prepared to put a new oring in it if it was real bad.
Logged
Reply #3August 09, 2011, 06:24:29 pm

burn_your_money

  • Global Moderator
  • Veteran
  • Offline
  • ***
  • 8999
  • Personal Text
    Bright, On
Re: removing vacuum pump
« Reply #3 on: August 09, 2011, 06:24:29 pm »
If it is that rusted in there CLEAN IT very well before removing it or you will get a bunch of junk in your engine. Lightly tapping it with a hammer side to side will get it out of there as well.

Personally I would not worry about it unless it took you over 2 months to do the headgasket job, but even then...
Logged
Tyler
Reply #4August 09, 2011, 06:47:12 pm

92EcoDiesel Jetta

  • Guest
Re: removing vacuum pump
« Reply #4 on: August 09, 2011, 06:47:12 pm »
Yeah I wire brushed it then sprayed it with Brake clean then penetrating oil soaking overnight.

Another reason I want to remove it is to paint it with POR15 along with the rusty injector hardlines. 
Logged
Reply #5August 09, 2011, 07:09:09 pm

Powered by Spearco

  • Veteran
  • Offline
  • ***
  • 1203
Re: removing vacuum pump
« Reply #5 on: August 09, 2011, 07:09:09 pm »
I wouldn't worry about oil pressure that much due to you'll be cranking it trying to frime the injectors. It'll get oil there before fuel.
Logged
'87 Syncro Transporter Single Cab "Now TDI"
'78 Rabbit..Gas Weekend Racer
'81 Caddy..Diesel 1.6/1.9 TD hybrid 275HP 349TQ "Retired"
'90 MultiVan, 2.5 Suby Swap, Porsche Brakes
'76 Scirocco TD dragster project
'13 Golf R:. Tuned
'98 Puch G320
Reply #6August 10, 2011, 08:21:05 am

silentdub

  • Junior
  • Offline
  • **
  • 135
Re: removing vacuum pump
« Reply #6 on: August 10, 2011, 08:21:05 am »
Not that it would hurt to do so, feel free to do it.

I only worry about it when I do rebuilds, but I use enough assembly lube to kill a small horse.



Logged
Reply #7August 10, 2011, 11:57:54 am

R.O.R-2.0

  • Veteran
  • Offline
  • ***
  • 7335
  • Personal Text
    Pacific Northwest - Oregon - USA
Re: removing vacuum pump
« Reply #7 on: August 10, 2011, 11:57:54 am »
grab that vacuum pump like it owes you money, and start twisting and tugging. it will come out..

like was stated, clean around it before you pull it.
Logged
92 Jetta GLI - Black, 1.6D w/ GT2056V turbo..
86 GTI - 4 Door, Med Twilight Gray, Tow Machine..
86 Audi Coupe GT - Tornado Red, All Stock.. WRECKED.
89 Toyota 4Runner - Dark Grey Metallic, LIFTED!

Turbo: exhaust gasses go into the turbocharger and spin it, witchcraft happens and you go faster.
Reply #8August 10, 2011, 05:33:07 pm

92EcoDiesel Jetta

  • Guest
Re: removing vacuum pump
« Reply #8 on: August 10, 2011, 05:33:07 pm »
I took a slide hammer, hooked the lip of the top plate and it moved. I didn't pull it out all the way (just 1/8 inch) so I can clean it up more then put it back till I'm ready to paint it.
Logged
Pages: [1]
« previous next »