-
6 speed box will it fit mk2 golf
by
snakemaster
on 26 Oct, 2010 13:35
-
-
#1
by
R.O.R-2.0
on 26 Oct, 2010 17:00
-
thats a PD TDI isnt it? its sexeh..
-
#2
by
snakemaster
on 28 Oct, 2010 11:50
-
thats a PD TDI isnt it? its sexeh..
it shure is a pd tdi 115hp
i think the box is a o2m can any one shed some light on this
-
#3
by
smiffie88
on 28 Oct, 2010 12:04
-
yeah box fits mk2 need to remake the two gearbox mounts and shorten the driveshafts you will also struggle with the speedo i think. theres a few guys done build threads on edition38 putting a pd and 6speed in a mk2
-
#4
by
R.O.R-2.0
on 30 Oct, 2010 11:39
-
everything mounts up completely different. it looks to me that it bolts in like a VR engine.. motor mounts bolted to the top of the frame horns..
and that trans has a jack shaft and equal length axles..
it would be ALOT of work, but most likely WORTH IT in the end.
-
#5
by
RadoTD
on 31 Oct, 2010 23:14
-
I think the box is a o2m can any one shed some light on this
I'm pretty sure you're right. They always look chubby and short.. IIRC o2j's still have the separate 5th/6th gear housing on the side where as the o2m has all the gears inside the case
@ the OP, you need to set up the hydraulic clutch, including newer pedal box, custom mounts and somehow mounting the shifter box inside the car. The mounting brackets are completely different for the o2m, so you need to fab up a way of mounting the shifter box in the right position too. I was looking into it before and if I remember right, that's all there is to it. Not easy, but far from impossible
-
#6
by
gldgti
on 08 Nov, 2010 23:23
-
That looks the the unit from a Transporter. You might find that if you tried to put it in a golf, the gearbox would be at a weirdo angle. In the transporter, the engine tilts forwards, but teh gearbox still sits the same as the golf - different bellhousing bolt pattern.
-
#7
by
R.O.R-2.0
on 11 Nov, 2010 05:41
-
That looks the the unit from a Transporter. You might find that if you tried to put it in a golf, the gearbox would be at a weirdo angle. In the transporter, the engine tilts forwards, but teh gearbox still sits the same as the golf - different bellhousing bolt pattern.
not like i am familiar with eurovan/transporter drivetrain, but i am familiar with the R/G/J drivetrain.. and now that you mention it, that engine IS tilted FORWARD!
-
#8
by
snakemaster
on 11 Nov, 2010 13:42
-
-
#9
by
rallydiesel
on 11 Nov, 2010 13:47
-
Do all the 02M have a jackshaft? That's kind of neat. I didn't know vw trans' could have those.
-
#10
by
Powered by Spearco
on 11 Nov, 2010 20:24
-
Euro Van had a jack shaft. There is a special mount to the back of the block that holds it. I know the trans is different sence it does not have a CV axle from it. They are the same 6spd but different bellhousing.
-
#11
by
G60ING
on 27 Nov, 2010 08:00
-
