Beer and Pizza for Clutch Help **Possible Custom Down Pipe**

[DVST8R]

Hey if anyone is good at doing VW, clutch's I could use a hand. I have done 1 FWD clutch and it was a pain, I have done lots of RWD/4WD clutch's, but no VW clutch's. :?

Anyway like the title says if you can lend a hand I am supplying Pizza and Beer, or your other favorite beverage. I have some airtools, lots of hand tools, a "lift" (big forklift).

:twisted: ***If your really good (ie. not much involvment from me, other then to hand you tools and beer) there will be a Custom Down Pipe in it for you, or other fab work if you would rather*** :twisted:

You can Email me, PM me or post up. I live in chillwack, but if you would rather do it at your place I am open to traveling within the lower mainland.

[steve]

Crap!  I missed out on another golden opportunity by living in Kansas.... :lol:

[Rat407]

Same here, would have done the job to have a custom down pipe made. Bummer living so far away from everyone.

[DVST8R]

Somebody Local??? I am going to start on it tonight with or without you :shock:

[lord_verminaard]

It's really not that hard.  I've never done one before my Rocco, and I think it took me all of 45 minutes to get the tranny out.  I think you only need like 3 sockets, a 17, a 19 and like a 12 or something.  Plus the 12-point socket for the flywheel.  I was suprised at how easy it was.  If you have more than one jack, now is the time to use them.    One under the engine, one under the tranny.   When the front, rear and drivers side mounts are loose, tilt the engine down toward the drivers side as much as possible, undo the bellhousing bolts, give her a yank, and make sure you dont have any body parts under the tranny when she goes.    Actually, a spot about three inches or so in front of the differential housing is a good place to put the jack, as the tranny balances pretty well there.  Good luck, you can do it!  

Brendan
84 Scirocco 8v
00 Camaro L36 M49

[DVST8R]

Anybody want to put it back in for a custom downpipe? I really don't want to fight with it anymore.  :roll:

Just the tranny I will have the flywheel pressure plate and clutch all on. I will have beer and pizza on hand as well.

Thanks.

[chrissev]

Anybody want to put it back in for a custom downpipe? I really don't want to fight with it anymore.  :roll:

Just the tranny I will have the flywheel pressure plate and clutch all on. I will have beer and pizza on hand as well.

Thanks.

Hello:  remember one thing:  if you let the weight of the transmission be supported by the mainshaft, you are going to need another transmission.

[935racer]

Hey man I can help you out, I need a custom downpipe too. And I live in abby so its good wen do you want to put it in? pizza and bear sounds awesome plus soem help with a dp. peace

[malone]

Hey man I can help you out, I need a custom downpipe too. And I live in abby so its good wen do you want to put it in? pizza and bear sounds awesome plus soem help with a dp. peace

You might want to give DVST8R your phone number so he can call you sooner.

You can send your # to him privately via "PM", by clicking the button at the bottom of DVST8R's post on this page.

[malone]

By the way I have seen DVST8R's custom downpipe last Saturday and it is very nice. All mandrel bent.

[DVST8R]

Thanks for the offer but its all in now. I managed to coral my buddy who is a mechanic for ford to get it in.

If you still need a custom dp pm me or email me I am sure we can work somthing out, If its a 1.9TD it might even be free.

[DVST8R]

for everybody else, stay tuned for custom DP coming to you in the near future.