VWDiesel.net The IDI, TDI, and mTDI source.
»
Engine Specific Info and Questions
» IDI Engine
View full version:
IDI Engine
«
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
»
Rebuilt injectors not firing
Vanagon 50º K14 drain angle
'81 rabbit N/A surging idle
K24 Downpipe stud size
idi or tdi
Oil rings
Paging all Holset turbo owners!
1.6td engine swap
Best of Both Worlds....1951 Diesel Beetle ! ! ! !
1.6/1.9td head gasket size
Coolant Flow.....MK2 1.6D??
Cam Seal R&R..."No Special Tools" Required
Timing Q
First Time Checking Pump Timing..Questions??
New guy with 1.6td
Compression Test Injector Adapter for 1.6 Mk2 Engine???
The Sound of Solenoids
Bosch VE Pump Manual
highest HP on vw idi achieved so far?
Goetze MLS AAZ head gaskets at Napa?
Built 1Y or Frankenengine? (and assorted other questions)
Where to buy pre chambers???
unable to start motor!
Any feedback on this master cylinder for 92 VW Jetta?
AAZ 8mm exhaust valve part numbers / length?
Bosch injector data dump
1.6 n/a throttle lever on pump sticking
more timing suggestions,
Preferred NA exhaust manifold?
piston ring T to NA ?
Ill never give up. 83' with 1.5D
Quieting the intake?
1.6 timing ?question?
Are VW 1.5NA and 1.6NA injections pump interchangable?
Crank bolt for JK block: Reuse, AHU bolt, or other?
Cranking speed, direct-drive vs gear reduction starters
aaz runing rought at ~2000 rpm
New Rabbit Owner!
head milling and head gaskets
Over or under sized crankshaft thrust washer
Congratulate me!
AAZ disastrous after IP reseal and calibration.
130 BAR SINGLE STAGE INJECTORS IN AAZ?
Boost pin position
What oil dipstick tube part# can be used in place of no longer available part#?
Instrument cluster lighting cuts out after 15 to 20 minutes
mk 1 vacuum pump leaking oil from lower outlet.
Stiffening motor mounts for racing application?
Is anyone running a t3 Garrett with a Volvo 760 cold side???
Where to buy metal AAZ head gasket?