ghostrider2 on 21 May, 2024 00:28 in IDI Engine
Here's the photos and videos as promised now:Here is a photo of the injector pump timing set to 0.9: https://share.icloud.com/photos/064BC4MzcBHpJ-pwJGzne6cqQHere's a video of the engine running and (you can't see it) but I push the cold start cable in and it stalls out. Please ignore the unfortunately timed air compressor turning on right at the end. You'll also hear my garage mate spraying the compressed air in the background (that's not my motor!) https://share.icloud.com/photos/03fCAdrAbU6B01hHT0huztHBQAnd here's a video of it running roughly and you can see the bypassed fuel system. Is it curious no fuel is coming out of the return line?https://share.icloud.com/photos/0a9Tmg8i1T0ZJb6v9h6M-1vEw
ghostrider2 on 21 May, 2024 00:26 in IDI Engine
Thanks y'all. That's encouraging because adjusting pump timing is something I know how to do now! And, yes, it has a turbo. Just the standard VW version though. Nothing fancy.
ORCoaster on 20 May, 2024 21:49 in IDI Engine
I would like to see you bump that pump to 1.25 and see what it does. Is this an engine with a turbo? Those should have 155 bar injectors so you can overcome some of the extra pressure that comes with increasing the air into the cylinder. At the same time, you have increased the pressure and you need to inject the fuel earlier so it will take advantage of the increase and force that piston down sooner and you get the benefit of the extra power. That is what I have going in the 1.6 diesel with a turbo on my PU and it seems to do better than if I run a standard 90 or an enhanced 1.05 mm timing.
fatmobile on 20 May, 2024 12:01 in IDI Engine
I think your instincts are right. The cold start lever is a great indicator of how well the timing is set.I don't think .9 is the recommended setting. At least around here it's closer to 1.
Dennis Froelich on 20 May, 2024 09:07 in IDI Engine
Even though they aren't the best place, PartsPlaceInc out of Michigan is probably the only place I think is available to find info on 1.9 IDI engines
cdsx on 20 May, 2024 07:19 in IDI Engine
Well, it appears my success was short-lived. After 84 views in 5 days, I'm sure someone would have mentioned a parts manual if one existed. Very disappointing.
ghostrider2 on 20 May, 2024 04:02 in IDI Engine
Hello everyone. I've spent the last year swapping a 1.6TD JX into my 1981 VW Vanagon (replacing a broken 1.7KY NA Motor). I've swapped everything from a donor vehicle that I test drove shortly before removing the motor and transmission. In the process I replaced most the seals and sensors (aside from the head gasket and injector pump). It's now finally in my bus, cranks and starts with the cold start pulled all the way out. When I give it gas or push the cold start back in it sputters and dies. Here's what I've checked so far:Set the belt timing to TDCSet the injection pump timing to 0.9Bled the injector linesFed fuel directly into the injector from a clean container to bypass the filter and make sure it wasn't a filter problemChecked for power at the solenoid and glow plugs - yesI have photos and video of the following but can't post them to the forum. I'll update the thread if I get permission.A photo of the injector pump timing set to 0.9.A video of the engine running and (you can't see it) but I push the cold start cable in and it stalls out. Please ignore the unfortunately timed air compressor turning on right at the end. You'll also hear my garage mate spraying the compressed air in the background (that's not my motor!) a video of it running roughly and you can see the bypassed fuel system. Is it curious no fuel is coming out of the return line?Only thing I can think of is to advance the pump timing but I don't really want to move it forward from the recommended settings until I've exhausted everything else. Thanks in advance for your help!
ORCoaster on 17 May, 2024 20:59 in Troubleshooting
Parts get old and worn. That was the case with my latch. I did manage to repair it enough to get it to work but I really wanted one in better shape. Glad I found one.
fatmobile on 17 May, 2024 01:57 in Troubleshooting
I haven't had that one happen in a while.
ORCoaster on 16 May, 2024 21:33 in IDI Engine
I seem to remember someone on this forum that has access to some form of exploded view drawings and part #s for the individual pieces but dang if I can remember who that person is