-
got my hands on a gtech pro
by
RabbitJockey
on 26 Aug, 2006 12:14
-
so i finally got my hands on a gtech pro, just borrowing it, i'm not all too impressed with it, it's very difficult to get it into mode, and in order for it to read horsepower i have to launch it for it to start reading i can't just be going down the road and put it in horpower mode and do a 3rd gear pull, and i dunno what's up with the quarter mile time deal, it never stoped reading. any suggestion on how to better it ?
-
#1
by
jackbombay
on 26 Aug, 2006 13:03
-
Is it the SS version? I've wanted one for a while, Malone is quite familiar with them I think, not sure what version he has though.
-
#2
by
RabbitJockey
on 26 Aug, 2006 13:05
-
no it's a gtech pro
-
#3
by
RabbitJockey
on 26 Aug, 2006 19:38
-
ok i got it better now, i didn't realize getting it zeroed and all that, it still seems to read very very low, my friends v8 mustang only pulled 95 hp...
-
#4
by
RabbitJockey
on 27 Aug, 2006 17:20
-
ok, i dunno how much better it is now, but i just started using it as more of a timer for 0-60 haha, looks to be around in 8-9 second range, it's hard to say since i have to drive at the same time, i'm sure you all understand, is that good? this is an 81 2 door jetta with no options and i turned the fuel screw in about half a turn to the right, and i have the boost pin turned to the deepest side and the star wheel down about 1.5-2 turns, it boost up to around 23 pounds. with a kkk turbo... lemme know thanks!
-
#5
by
SMOKEYDUB
on 27 Aug, 2006 19:58
-
you have to have the weight of the vehicle very very close for it to be acurate. thats what i have found. i gteched my car 130 hp
good luck figuring that thing out i have the old version so its easy.
-
#6
by
RabbitJockey
on 28 Aug, 2006 14:24
-
i need to weigh my car for sure, but for now looky what i ran, the trap speed seems high
-
#7
by
RabbitJockey
on 28 Aug, 2006 14:28
-
yeah that et is closer to one for someone doing a second faster quarter, but my car does have alot of *** in the higher gears, especially with the closed wastegate
-
#8
by
sethyboy85
on 28 Aug, 2006 17:15
-
they read a high MPH those models, I ran a 14.9 @ 99mph and then at the track did 15.2@ 93 or something like that back when my dayonta was unmodded.
Still have the Gtech laying around somewhere...
-
#9
by
Kudagra
on 28 Aug, 2006 17:25
-
I think those things are like stickers on hondas.
Why not find a dyno and take it to the track?
-
#10
by
sethyboy85
on 28 Aug, 2006 17:27
-
real dynos for a diesel are non existant around here, I know because a normal dyno is difficult to find let alone use...
We plan to go drag racing next month or after that but before hand it is fun to see how accurate a piece of plastic can be.
-
#11
by
malone
on 28 Aug, 2006 17:56
-
Is it the SS version? I've wanted one for a while, Malone is quite familiar with them I think, not sure what version he has though.
I have the RR. Bought it on ebay some time ago.
I used to have Gtech Pro like Trev0rbr's and I felt unsatisfied with it because accurate RPM calibration is not possible. It also does not show or record HP and Torque
curves. It just displays peak HP. It's ok for checking differences in 0-60mph and 1/4 mile times after modifications.
The newer Gtech Competition, SS, RR, etc. models with three built-in accelerometers and HP/Torque plotting is better by far. Results are very consistent with proper calibration.
HP and torque numbers in Gtech are always lower than numbers from a typical dyno. A 172bhp VR6 that dynos ~155whp reported around 135 net HP in Gtech if I remember correctly.
-
#12
by
jackbombay
on 28 Aug, 2006 18:29
-
I used to have Gtech Pro like Trev0rbr's and I felt unsatisfied with it because accurate RPM calibration is not possible. It also does not show or record HP and Torque curves.
That's why I want one, Actuall dyno pulls run, what? $100 for 3? Or the g-tech is $200 for unlimited "dyno pulls"?