-
tips for removing 1.6D injection pump sprocket?
by
TimpanogosSlim
on 09 Mar, 2014 22:00
-
I'm just about ready to yank the engine out of my 84 coupe.
however, the sprocket won't come off of the injection pump. It has to come out because i have a 1.6TD pump to install.
After talking to zukgod1 i tried the method of removing all of the mounting bolts for the pump, putting a pry bar behind the sprocket - pushing the sprocket out against the mounting bracket - and tapping the loosened nut with a hammer.
And i kept prying and tapping for about 40 minutes. It hasn't budged.
it's a rebuilt pump. Whatever rebuilder puts a dab of yellow paint on every screw.
i suspect that it has been over-torqued.
I am a little tempted to try heating the sprocket, but there are obvious risks
I hear that a standard 2-finger puller may break the sprocket.
Any ideas?
-
#1
by
745 turbogreasel
on 09 Mar, 2014 23:16
-
I usually pry from 2 sides by driving a couple wood chisels or other wide metal taper between sprocket and bracket, then tap the end of the shaft with a brass hammer.
Prying form only one side a) binds on the shaft b) bends the sprocket pretty easy,so don't do that unless the sprocket is already bent.
I did make something like this out of hardware store bolts and angle iron that worked OK too...but mine uses the (ground to fit) head of the bolt as the puling hook.
-
#2
by
TimpanogosSlim
on 10 Mar, 2014 05:41
-
The pry bar i was using was kinda short but i was not putting pressure on the outer diameter of the sprocket - but on the inside near the hub.
pressure from two places would end up being on the teeth rather than near the hub.
I could 'customize' some bolts and use a duck's foot i suppose.
-
#3
by
burn_your_money
on 10 Mar, 2014 18:27
-
Very loosely put the big nut on the pump. Use a prybar between the pulley and pump mount and put some decent pressure on it. If it doesn't pop off, carefully tap the edge of the pulley with a brass hammer. Actually hit it as hard as you can squarely. It will pop off.
-
#4
by
Jetmugg
on 11 Mar, 2014 09:57
-
Yep, I second (or third, or whatever) the notion that what's needed is a decent dose of static pressure, balanced on at least 2 points, combined with a sharp radial impact (brass hammer), or an axial impact applied to the centerline of the puller.
Boing!
-
#5
by
TimpanogosSlim
on 11 Mar, 2014 13:21
-
Alright. I browsed a local freight salvage place for a brass hammer today, but all they had were fancy brand 4lb models that they wanted $66 for.
I have a good brass drift but it is longer than the available space. I guess i could whack it sideways tho.
-
#6
by
bajacalal
on 11 Mar, 2014 13:58
-
I really would suggest a pulley puller, with the different attachments I think you can make something work, iirc I used the typical 3/2 combination arbor last time with some long bolts and washers and it worked pretty well. It's easy to damage the injection pump if you don't pull the pulley straight off with no lateral force because the shaft is really pretty thin and the bearings that support the shaft, I think it's actually a bushing and not very robust.
-
#7
by
fatmobile
on 11 Mar, 2014 14:31
-
I usually pry from 2 sides by driving a couple wood chisels or other wide metal taper between sprocket and bracket, then tap the end of the shaft with a brass hammer.
That's what I do.
learned it from Libby.
It's not really prying when you tap a wedge down between the bracket and sprocket, you don't pull it to the side, just tap it straight in like a wedge.
Opposite sides of the sprocket.
Loosen don't remove the nut first and a couple final smacks on the sprocket can rock it off.
-
#8
by
burn_your_money
on 11 Mar, 2014 14:53
-
It's easy to damage the injection pump if you don't pull the pulley straight off with no lateral force because the shaft is really pretty thin and the bearings that support the shaft, I think it's actually a bushing and not very robust.
I would be absolutely amazed if you could do any damage at all the the pump shaft by removing the pulley, short of damaging the threads if you hit it with a hammer. Those shafts are extremely tough. Also, there is a lot of surface area on the brass? plated bushings, you aren't going to damage them. I'm pretty sure you would crack the pump body first.
-
#9
by
damac
on 12 Mar, 2014 18:27
-
I never even thought of using anything besides a puller.
I got the one below at harborfreight and grinded away just enough so each arm would fit through ip sprockets with the opposing big holes. Took the tip off so the dimple will fit right into the recess with the nut backed off a tad as a guide and a few cranks and pop every time.
http://www.harborfreight.com/automotive-pulley-puller-66868.html#.UyEJOIWwXHs
-
#10
by
JamesT
on 12 Mar, 2014 23:15
-
I would always use a puller. If you damage the sprocket slightly and don't notice, it might cause belt failure down the road. I wouldn't risk it.
-
#11
by
TimpanogosSlim
on 12 Mar, 2014 23:54
-
funny thing is i was advised that a 2-finger puller would probably break the pulley.
I have a duck's foot. I'll give it a try with some modified bolts.
-
#12
by
vanbcguy
on 13 Mar, 2014 19:40
-
I used a 2 arm puller on mine, no issues. It did leave some marks on the back of the pulley though.
Sent from my HTC One XL using Tapatalk