-
I need a 210mm flywheel WITH TDC mark!
by
erice1984
on 24 Sep, 2012 01:12
-
Anyone know where one could be?
I have one from a digifant gasser and no TDC. I have timed this engine ~10-15 times and only had 1 time I considered acceptable. Bottom line is, this is wasting my time and would like to get a hold of a 210mm flywheel with a factory TDC mark.
Thanks
-Eric
EDIT: This MUST fit a 020 transmission.
-
#1
by
theman53
on 24 Sep, 2012 08:08
-
AAZ from canada
-
#2
by
CRSMP5
on 24 Sep, 2012 08:13
-
tdc on a mk2 210mm flywheel is beside a bolt.. its just a dimple... not a cut out.....
-
#3
by
erice1984
on 24 Sep, 2012 14:49
-
AAZ from canada
AAZ from CA had a 210mm setup? I thought it was 228mm..
Ah ha! I see it now, the Passat with AAZ had 228mm the Jetta with AAZ had 210mm
-
#4
by
erice1984
on 24 Sep, 2012 15:08
-
027105271nx - Sachs P/N: W0133-1599035 At
www.autohausaz.com I can see the TDC mark in the picture, nearest the bolt hole.
VERIFIED the above part number does have the TDC mark on it.
027105271p shows up as fitting cabrio etc... (gas engines, I assume this does not have TDC mark.)
Thanks for the lead theman53
-
#5
by
CRSMP5
on 24 Sep, 2012 16:01
-
why not??? timming belt... gotta know tdc on them too....
what i find is someone screws up and forces it on when doing clutch job... aka ignored dowles and got it in the other 2/3 ways it can bolt on incorrectly.. but all vw that it fits has tdc for timming belt...
-
#6
by
theman53
on 24 Sep, 2012 21:13
-
I have a couple aaz in the shed. I will see if I have a flywheel I can part with.
-
#7
by
erice1984
on 24 Sep, 2012 21:15
-
I have a couple aaz in the shed. I will see if I have a flywheel I can part with.
Don't worry about it. I ordered a new one from autohausaz. I appreciate the offer though.
-
#8
by
R.O.R-2.0
on 25 Sep, 2012 13:20
-
I have a couple aaz in the shed. I will see if I have a flywheel I can part with.
Don't worry about it. I ordered a new one from autohausaz. I appreciate the offer though.
the mk2 gassers with CIS had a TDC mark, and usually degree marks as well..
i use early mk2 CIS flywheels.. a STOCK gasser flywheel is like a lightened flywheel on a diesel.
Lucas, if you have an 020 flywheel off an AAZ, would you snap some pics for me, or simply weigh it?
-
#9
by
theman53
on 25 Sep, 2012 17:27
-
12.8lbs
I am 99% sure on that, I looked for the flywheels but I am loosing stuff until the shed is done. I couldn't find it, but I remember weighing mine and I pretty sure it weighed 12.8lbs. If it wasn't 12.8lbs it is 12.6 for sure one of the 2 is correct.
-
#10
by
8v-of-fury
on 25 Sep, 2012 21:54
-
My 210mm 020 Gas flywheel was easily twice as light as the 228mm 02A TDI flywheel I took off the engine lol. SUPER UPGRADE !
-
#11
by
R.O.R-2.0
on 26 Sep, 2012 14:51
-
12.8lbs
I am 99% sure on that, I looked for the flywheels but I am loosing stuff until the shed is done. I couldn't find it, but I remember weighing mine and I pretty sure it weighed 12.8lbs. If it wasn't 12.8lbs it is 12.6 for sure one of the 2 is correct.
ok, cause the 16v flywheel i just installed on my diesel, was ~13#s
02A flywheels ARE easily TWICE as much..
-
#12
by
theman53
on 29 Sep, 2012 15:20
-
I have a couple aaz in the shed. I will see if I have a flywheel I can part with.
Don't worry about it. I ordered a new one from autohausaz. I appreciate the offer though.
Can you do me a favor and when you get this measure it. I and a friend of mine want to know what the actual face to face measurement is on an unmolested flywheel. That way we could know if there is a problem when resurfacing. Thanks Lucas><>
-
#13
by
erice1984
on 29 Sep, 2012 17:39
-
I have a couple aaz in the shed. I will see if I have a flywheel I can part with.
Don't worry about it. I ordered a new one from autohausaz. I appreciate the offer though.
Can you do me a favor and when you get this measure it. I and a friend of mine want to know what the actual face to face measurement is on an unmolested flywheel. That way we could know if there is a problem when resurfacing. Thanks Lucas><>
Will do.
-
#14
by
erice1984
on 29 Sep, 2012 17:42
-
This flywheel, I forgot to check which trans version it is for. It is not going to work in a 020. Damnit.
EDIT: The flywheel is in fact meant for 020, just a later version, the 16v. Not sure if it will work under the 8v transmission I have.