« previous next »
Pages: 1 [2]

Author Topic: Tools by location thread  (Read 18642 times)

Reply #15December 11, 2011, 11:01:57 am

R.O.R-2.0

  • Veteran
  • Offline
  • ***
  • 7335
  • Personal Text
    Pacific Northwest - Oregon - USA
Re: Tools by location thread
« Reply #15 on: December 11, 2011, 11:01:57 am »
Quote from: oldpoopie on December 10, 2011, 09:18:56 pm
VCDS
Wheel bearing tools
Timing belt tools
intermediate shaft bearing tools.

Lots lots more

what tools are required to do wheel bearings?
Logged
92 Jetta GLI - Black, 1.6D w/ GT2056V turbo..
86 GTI - 4 Door, Med Twilight Gray, Tow Machine..
86 Audi Coupe GT - Tornado Red, All Stock.. WRECKED.
89 Toyota 4Runner - Dark Grey Metallic, LIFTED!

Turbo: exhaust gasses go into the turbocharger and spin it, witchcraft happens and you go faster.
Reply #16December 11, 2011, 10:41:09 pm

CRSMP5

  • Guest
Re: Tools by location thread
« Reply #16 on: December 11, 2011, 10:41:09 pm »
for me.. on car.. slide hammer to yank hub out.. snap ring pliers for the snap ring.. portable press tool with pieces to press it out via wrench/ratchet.. aka can do on car type of thing.. air chissel to knock inner race off hub.. use same press tool to reinstall hub..

other tools.. axle nut socket.. ball joint pinch bolt removal tools.. impact driver to remove set screw holding rotor to hub.. socket to remove caliper.. caliper carrier if you can..

now no portable press tool.. gotta have a press to remove the bearing and press hub in.. and the socket to remve upper strut from body so you do not screw up alignment.. and a socket/wrench for tie rod end..
Logged
Reply #17December 17, 2011, 04:54:21 pm

somedumbjerk

  • Junior
  • Offline
  • **
  • 71
Re: Tools by location thread
« Reply #17 on: December 17, 2011, 04:54:21 pm »
triple square/12pt 6, 8, 10 an 12mm
idi timing kit
compression tester
engine stand  ;D
located in Palo Alto CA.
Logged
Reply #18January 25, 2012, 06:45:34 pm

Syncroincity

  • Veteran
  • Offline
  • ***
  • 727
Re: Tools by location thread
« Reply #18 on: January 25, 2012, 06:45:34 pm »
Queens, New York

Engine hoist crane
Engine stand
Compressor & air tools; impact gun, air hammer, grinder etc
Tripple-square full set & most allens (also 17mm trans plug allen)
IDI timing tools & dial indicator
Spring compressors
Torque wrenches: click & deflection
Vanagon axle nut (46mm) socket & hammer tool
Injector socket
02 sensor sockets
Pickle fork
Ramps
Wire-feed MIG welder
Cylinder bore gauge
Cylinder hone (3-stone)
OBDII scan tool - generic, not vag-com
Fluke meter
Logged
JC McCavitt
'86 Syncro GL Camper AAZ
'98 Jetta Wolfie
'04 Passat Variant GLS 4Mo 5MT
Reply #19January 25, 2012, 07:56:21 pm

CRSMP5

  • Guest
Re: Tools by location thread
« Reply #19 on: January 25, 2012, 07:56:21 pm »
44505 area.. ne ohio... full shop w lift, vagcom.. tools.. mig and tig.. no tire machines though.. and bosses thought on retiring in the fall means i have no idea... he keeps talking tire machine though...
Logged
Reply #20March 06, 2012, 11:18:20 pm

oldpoopie

  • User+
  • Offline
  • *
  • 46
Re: Tools by location thread
« Reply #20 on: March 06, 2012, 11:18:20 pm »
Quote from: R.O.R-2.0 on December 11, 2011, 11:01:57 am
Quote from: oldpoopie on December 10, 2011, 09:18:56 pm
VCDS
Wheel bearing tools
Timing belt tools
intermediate shaft bearing tools.

Lots lots more

what tools are required to do wheel bearings?

Hub tamer elite lets me change wheelbearings without pulling the hub.
Logged
1985 jetta TD. It was free, and it shows. Down and dirty engine refresh made it run fairly well.... No leaks, except water into the cabin!

2001 golf Tdi. Heavy built ALH, soon to have a PD Frankenstein motor.
Reply #21March 09, 2012, 09:51:33 pm

pointynoggin

  • Junior
  • Offline
  • **
  • 93
Re: Tools by location thread
« Reply #21 on: March 09, 2012, 09:51:33 pm »
Armstrong bc

timing tools
assorted engine work tools
Logged
1991 Jetta 1.6TD, Giles Superpump,
Reply #22April 12, 2012, 09:14:05 am

guy plain

  • Junior
  • Offline
  • **
  • 121
Re: Tools by location thread
« Reply #22 on: April 12, 2012, 09:14:05 am »
any one around kamloops or close to....even vancouver have the timing tools for a 1.6 td? thanks in advance for any replys
Logged
Reply #23April 28, 2012, 08:17:49 am

92EcoDiesel Jetta

  • Guest
Re: Tools by location thread
« Reply #23 on: April 28, 2012, 08:17:49 am »
Governor mod tool.  Queens NY. you are welcome to borrow it. local loan only, no mail.

This tool makes shimming the governor a breeze.

Logged
Reply #24April 28, 2012, 09:12:17 pm

billybobf

  • Veteran
  • Offline
  • ***
  • 318
  • Personal Text
    89 golf 1.8 digi, 1.6 na in pieces in the shop
Re: Tools by location thread
« Reply #24 on: April 28, 2012, 09:12:17 pm »
florence oregon.

mig welder,
engine hoist
engine stand
cylinder boring bar
harbor freight compression tester and three stone cylinder hone.
soon to be pop tester, need an 8mm dial indicator to run the pump timing adapter I bought.
sure i have some other stuff. pressure washer.
Logged
Pages: 1 [2]
« previous next »