Author Topic: volvo d24tic crank tool (Read 9213 times)

MRDART · « **on:** March 06, 2009, 01:18:31 pm »

HI guys!
Anyone know of a good tool to hold the crankshaft whilst loosening/torqueing the front crank pulley bolt?

I made one years ago but it did not hold up very good and did not work so good either.
Anyone have any links to a tool or maybe a good picture with measurements? I know a very good toolmaker so if I can only get a drawing it would be a piece of cake best regards / Tommy

the caveman · « **Reply #1 on:** March 06, 2009, 02:51:52 pm »

I asked the same thing a few months ago
-http://vwdiesel.net/phpBB/viewtopic.php?t=14974&highlight=
No answers but like it says, the pulley came off by hand! To tighten it I seem to remember just using a prybar and visegrips to hold the pulley somehow. It worked because i got it to torque up to spec. I would imagine the same thing to remove it. If you have a compressor and a strong impact gun it should also be able to remove it.

v8volvo · « **Reply #2 on:** March 14, 2009, 10:40:52 am »

Try talking to Baum Tools, they sell all this stuff and may be able to tell you the dimensions.

http://www.baumtools.com/contact.php

Or look here:
volvoturbodiesel.blogspot.com

the caveman · « **Reply #3 on:** March 14, 2009, 01:03:18 pm »

The volvo blogspot is a great resource for that motor.
I searched for a tool that would work, but i looked at VW and Volvo dealer tools and didn't find. However there must be be a supplier in Europe

v8volvo · « **Reply #4 on:** March 15, 2009, 02:11:21 pm »

Call Baum Tools at the 800 number you see on the link I posted. The guys really know what they are talking about and will be able to help you out. I spoke with Dexter there last week and he seemed really glad to be talking to someone who still had one of these motors. As you know, they are really rare...

I think that crank holder tool also works for Audi 5cyl gassers, so it's not that odd.

cuaz64 · « **Reply #5 on:** April 09, 2009, 05:32:59 pm »

Check volvoturbodiesel.blogspot.com. There exist an entry about the crank holder tool of Baum tools. Also you can check there fragments of service manuals.

MRDART · « **Reply #6 on:** April 13, 2009, 12:22:28 am »

I know about the volvoblog it is a great source of info.
I have a friend who is a toolmaker and he said just give me the pulley and i will make the tool... so that is gonna be very nice since I´ve seen all the other special tools he made for aircraft maintenance......

snakemaster · « **Reply #7 on:** April 19, 2009, 11:08:41 am »

i put a chisel in the ring and held it agenst the gearbox worked ok for me

dieseltech · « **Reply #8 on:** July 31, 2009, 07:27:08 pm »

snap on's cheaper brand blue point sells the proper tools, but you have to look for the audi 5 cylinder gas or diesel, they both use the sme 2 tools, one is the crank holder, the other is the torque wrench extension that gives you the correct torque

MJF · « **Reply #9 on:** August 07, 2009, 03:44:34 pm »

If you can´t find a proper tool, you could always do this

Found it from my 2,5TDI Audi, I made my own tool to hold crank.

dennis · « **Reply #10 on:** September 16, 2009, 12:58:21 pm »

IMpact gun off. Impact gun on.

the caveman · « **Reply #11 on:** September 16, 2009, 03:36:30 pm »

Quote from: dennis on September 16, 2009, 12:58:21 pm

IMpact gun off. Impact gun on.

No room on a volvo for that.Even with a swivel. i would have done it otherwise.

dennis · « **Reply #12 on:** September 19, 2009, 08:06:44 am »

Radiator hasto be out. Did it.

Author Topic: volvo d24tic crank tool (Read 9213 times)

MRDART

volvo d24tic crank tool

the caveman

volvo d24tic crank tool

v8volvo

volvo d24tic crank tool

the caveman

volvo d24tic crank tool

v8volvo

volvo d24tic crank tool

cuaz64

volvo d24tic crank tool

MRDART

volvo d24tic crank tool

snakemaster

volvo d24tic crank tool

dieseltech

Re: volvo d24tic crank tool

MJF

Re: volvo d24tic crank tool

dennis

Re: volvo d24tic crank tool

the caveman

Re: volvo d24tic crank tool

dennis

Re: volvo d24tic crank tool