-
Boost controller
by
MontanaGTD
on 02 Sep, 2007 16:21
-
I have a Garrett Turbo on my GTD - where do i fit the boost controller?
There is a solid metal pipe which runs front the side of the turbo (with a Banjo connector on the end I can see) and it runs around the back of the turbo and goes back into the back of the turbo - i've traced all the water / oil pipes and dont thing that that is one of them Am I right? Or can some one spread some light on this with a few pics??
-
#1
by
MontanaGTD
on 02 Sep, 2007 16:41
-
-
#2
by
jimfoo
on 02 Sep, 2007 19:29
-
That sounds like where it should hook into. The metal pipe should go to the waste gate from the compressor scroll.
-
#3
by
Choppercat
on 03 Sep, 2007 07:40
-
I just installed a boost controller a month ago on my 1.9. It came with a ''T'' with a restriction built into it. I installed it with the arrow pointing toward the waste-gate and the valve went into the modified ashtray for a stealth look. Then I went for a test drive and to my surprise, even with the valve fully closed the boost climbed to 15 psi. I never wanted to go past 15 so goodbye adjustability! I replaced the restricted Tee with a free flowing one and the boost dropped back to normal and I can now open the valve to adjust boost where I want it. Before installing it I did some research mainly on this forum and some recommended putting Tees and check-valves in the system but in my opinion check-valves are not required on a diesel as there is no vaccuum in the intake. Am I right or did I miss something?
-
#4
by
MontanaGTD
on 03 Sep, 2007 08:45
-
Mine doesnt have a check valve on it - its just the adjuster - I was sure it was the right pipe, even before I asked - but I wanted to make 100% sure before I go cutting it with the saw! Just need to fit my 3" straight through exhaust and i'm set!
-
#5
by
Choppercat
on 03 Sep, 2007 09:06
-
Coincidence! I took my exhaust out of the car yesterday and was planning a visit to the muffler shop this week for a 2.5'' straight pipe from the down pipe back. Let me know how it souds! I ran mine last night with no exhaust at all and it's loud! But I could have been listening to the turbo all night.
-
#6
by
foxracer1
on 03 Sep, 2007 11:01
-
My buddy has a 2.5" straight pipe from turbo back on a 1.9 w/ K14 it sounds relativley quiet. And yes the turbo is sweet sounding.
-
#7
by
Demons UK
on 03 Sep, 2007 11:46
-
i've got a 2.5 straight through on my GTD.
Its louder then most exhausts, it sounds like a bad boy racer car mixed with a tractor tbh, the sounds pretty cool through and gets very queit after a few thou revs.
-
#8
by
numbnuts
on 03 Sep, 2007 12:44
-
Mine doesnt have a check valve on it - its just the adjuster - I was sure it was the right pipe, even before I asked - but I wanted to make 100% sure before I go cutting it with the saw! Just need to fit my 3" straight through exhaust and i'm set!
If U are doing this, can u take some pics as i plan on doing this on mine? :lol:
Also what boost controller have u got and what exhaust?
Thanks alot, Joel
-
#9
by
rallydiesel
on 03 Sep, 2007 12:48
-
You probably already know this but don't forget to block off your intake relief valve (if the GTD even had this?).
-
#10
by
MontanaGTD
on 03 Sep, 2007 12:57
-
This is the boost controller I fitted :-
The quote at the bottom of the listing from polo6n1600i is me!
http://cgi.ebay.co.uk/POWERTEK-BOOST-CONTROLLER-MK-2-GOLF-GTD_W0QQitemZ140153275484QQihZ004QQcategoryZ10428QQssPageNameZWDVWQQrdZ1QQcmdZViewItemI'm running a VAG downpipe (its off a GTD which didnt have any front silencer box) and I'll be fitting a complete Ashley Rally System. I'm a trader and got it at a huge discount direct from Ashley. Its a 3" straight through with 1 single can on the back and it end in twin 2.5" round pipes. I had one of their 2" systems on one of my old Golf GTi's and it was pretty loud. cant wait to hear what it sounds like on the GTD!
Oh and even with the controller just turned out 1/2 a turn i'm seeing just over 1 Bar of boost! Plus i've tweeked the fuel screw back 1/8 of a turn and it doesnt smoke like it use to. Cars in the rear view mirror use to dissappear!
-
#11
by
con
on 03 Sep, 2007 13:16
-
Hey montanaGTD if you get a chance could you snap me a pic of your freshly installed boost controller too?
-
#12
by
MontanaGTD
on 03 Sep, 2007 13:18
-
Will do! I'm still messing with the pipework to get it up under the dash - Its currently in the service book slot and I can adjust it of i want, but it isnt easily to hand. So i'm thinking about getting some more pipe and remounting it through one of the switch blanks in the dash beside the speedo clocks.
-
#13
by
MK2 GTD
on 03 Sep, 2007 16:15
-
MontanaGTD
Wouldnt mind a few pictures of the boost controller install, also where did you T off for the pressure gauge.
Am in the process of fitting my radio into the bottom slot of a genuine Votex console, top slot for electric window switches. Putting a set of VDO, Oil Pressure, OilTemperature and Boost gauges where the radio should be.
Hopefully get a few pictures of the install.
-
#14
by
MontanaGTD
on 04 Sep, 2007 05:33
-
Same with me:-
Gauges were the stereo normally fits, stereo in the lower vortex panel and electric windows switch in the upper vortex panel.