VWDiesel.net The IDI, TDI, and mTDI source.
Engine Specific Info and Questions => IDI Engine => Topic started by: Kantdrivefast on April 01, 2009, 04:15:26 pm
-
Well I got around to taking the head off and found these.
(http://i147.photobucket.com/albums/r317/casman66/IMG_9177.jpg)
(http://i147.photobucket.com/albums/r317/casman66/IMG_9179.jpg)
(http://i147.photobucket.com/albums/r317/casman66/IMG_9180.jpg)
(http://i147.photobucket.com/albums/r317/casman66/IMG_9178.jpg)
How bad are these. Worth rebuilding?
-
daily or race car?
-
Daily with a little more fuel and boost.
Nothing too fancy.
Whats the verdict..... find a new one? Or put this one together?
-
can you get just new pre cups?
-
Where from. I searched the thread and all I could come up with was that new ones are pretty much pure unobtainium.
I was also referring to the cracks inbetween the valves. Are they too large?
-
new swirl chambers are available. i recall viewing a post linking to a vendor that listed a plethora of different chambers of all types for all makes. don't know where it is now, and a search might take a while to sift through.
-
I wouldn't worry too much about the cracks between the valves they are pretty normal. Bentleys even gives a spec for the max size and those don't look even close. Cheers Dan
-
You got to get ahold of this guy: http://forums.tdiclub.com/member.php?u=31923
He does IDI heads too. I'm going to send him the one from my '89 for a complete refurbishing. It needs it. 8)
-
will a 1.9 precup fit in a 1.6 head?
-
will a 1.9 precup fit in a 1.6 head?
i'm pretty sure they're a bit bigger. which is why using the 1.9 head on the 1.6 makes it a little harder to start.
frank06 on TDIclub only does TDI heads though right??? maybe he can get the swirl chambers though?
-
will a 1.9 precup fit in a 1.6 head?
i'm pretty sure they're a bit bigger. which is why using the 1.9 head on the 1.6 makes it a little harder to start.
frank06 on TDIclub only does TDI heads though right??? maybe he can get the swirl chambers though?
Nope, he can do both IDI and TDI. You would have to ask him about the swirl chambers though. 8)
-
will a 1.9 precup fit in a 1.6 head?
i'm pretty sure they're a bit bigger. which is why using the 1.9 head on the 1.6 makes it a little harder to start.
frank06 on TDIclub only does TDI heads though right??? maybe he can get the swirl chambers though?
Nope, he can do both IDI and TDI. You would have to ask him about the swirl chambers though. 8)
ah pretty cool! hopefully he doesn't charge too much. those new chinese heads are very cost effective :lol:
-
will a 1.9 precup fit in a 1.6 head?
i'm pretty sure they're a bit bigger. which is why using the 1.9 head on the 1.6 makes it a little harder to start.
frank06 on TDIclub only does TDI heads though right??? maybe he can get the swirl chambers though?
Nope, he can do both IDI and TDI. You would have to ask him about the swirl chambers though. 8)
ah pretty cool! hopefully he doesn't charge too much. those new chinese heads are very cost effective :lol:
I don't even know where one could get a genuine German head... :x
-
My vote... for a daily driver the head appears fine... cracks between the valves are smaller than many I've seen (in general a dime is the thickness limit), and the pre-chambers are beginning to show some stress fractures but given how thick they are they probably have many many miles left.
I'd have it surfaced, rebuilt as required (guides, seals, etc) and carry on.
-
As another reply to the valve cracks coming from a guy who had to get a new head because of them....
my cracks in my 1.6head were enormous in comparison. An actual gap. Just visible cracks are nothing man. I wasn't so forum savy back then and i didn't think to take pictures of how big they were to show how big mine were to screw over my cooling system.
I later threw it into the local "transfer station" pit with much rejoicing following.
-
will a 1.9 precup fit in a 1.6 head?
i'm pretty sure they're a bit bigger. which is why using the 1.9 head on the 1.6 makes it a little harder to start.
frank06 on TDIclub only does TDI heads though right??? maybe he can get the swirl chambers though?
Nope, he can do both IDI and TDI. You would have to ask him about the swirl chambers though. 8)
ah pretty cool! hopefully he doesn't charge too much. those new chinese heads are very cost effective :lol:
Mine hasn't grenaded yet!!!!!! and that's with max stock fueling and ZERO boost control!!! 20 psi regularly.
-
My vote... for a daily driver the head appears fine... cracks between the valves are smaller than many I've seen (in general a dime is the thickness limit), and the pre-chambers are beginning to show some stress fractures but given how thick they are they probably have many many miles left.
I'd have it surfaced, rebuilt as required (guides, seals, etc) and carry on.
This was the kind of reply I was looking for. Thanks vince. Now, head resurfacing? Machine shop does this I imagine or can I just run a flat block on it with 1000 grit or so, and if it goes to the machine shop do the precups have to come out, and should I peen them in? And if I do, how would I go about doing it.
So many questions... so much left to do.
-
will a 1.9 precup fit in a 1.6 head?
There are 2 size of 1,9 precup. Other (earlier?) will fit to 1,6 head, but has bigger opening. The other is smaller in diameter and will not fit.