VWDiesel.net The IDI, TDI, and mTDI source.

For Sale/Looking For => Parts for Sale/Wanted => Topic started by: Dakotakid on September 27, 2013, 09:02:06 am

Title: WTB early 1.6 crank sprocket with non-integrated key
Post by: Dakotakid on September 27, 2013, 09:02:06 am

I am currently working on a "CR" code ('82 Jetta) engine and am in need of a good non-integrated front (where else?) crankshaft sprocket.

These fit the earlier crankshaft which has the narrow keyway and actually utilizes a key which is seperate from the sprocket.

I actually even forgot these exist as everything I run utilizes the newer integrated sprocket and key.

I may have one in my storage mess and will start looking for it later today. But THAT is a herculean task at the slightest.....right up there with waterboarding. So if you have a non-damaged one......let's talk.

Title: Re: WTB early 1.6 crank sprocket with non-integrated key
Post by: CRSMP5 on September 27, 2013, 12:46:18 pm

jetmug speed tester guy found one over a yearago.. id pm him with a where did you find it.. :P

same as old 1.5 fyi...  theman asked me abt same sprocket yesterday... also as a  special washer too...

Title: Re: WTB early 1.6 crank sprocket with non-integrated key
Post by: Dakotakid on September 27, 2013, 06:49:34 pm

Yes, and thanks. I crawled through over 50% of my crap today and did not come up with one.

Still looking and please PM me if you have one.

Title: Re: WTB early 1.6 crank sprocket with non-integrated key
Post by: CRSMP5 on September 27, 2013, 07:22:54 pm

ohh i has.. but i also has the crank and long block it goes on.. :P so not for sale.. running engine...

Title: Re: WTB early 1.6 crank sprocket with non-integrated key
Post by: Dakotakid on September 27, 2013, 07:54:07 pm

Right.
I'm starting to think I never had one of these on hand. You see....that was the deal with my original 1.5. That engine just ran and ran and ran....never needed any work. Then, the ex-wife ran it into a concrete block retaining wall one bright sunny morning.

Women......

That was about the time being single didn't look so bad........

Title: Re: WTB early 1.6 crank sprocket with non-integrated key
Post by: libbydiesel on September 27, 2013, 08:40:45 pm

I know I have at least two of them, maybe three, but the question is where?  I'll keep an eye out.

Title: Re: WTB early 1.6 crank sprocket with non-integrated key
Post by: Dakotakid on September 27, 2013, 11:12:41 pm

When all else fails.....check ebay.
Bryan in Purcell, OK had one. Dun bought it.

Title: Re: WTB early 1.6 crank sprocket with non-integrated key
Post by: fatmobile on September 28, 2013, 10:10:08 pm

I have a couple extras.
 Just gave one to my buddy so I even know where they are.
PM me and we'll figure out payment.

Title: Re: WTB early 1.6 crank sprocket with non-integrated key
Post by: Toby on September 29, 2013, 10:37:58 am

I am sure that I have some. I will look today.

Title: Re: WTB early 1.6 crank sprocket with non-integrated key
Post by: Rabbit79 on September 29, 2013, 12:49:29 pm

I believe these are the ones you're looking for if you want to go new. This is the only place I've found that still has them.

http://www.busdepot.com/049105263b

Title: Re: WTB early 1.6 crank sprocket with non-integrated key
Post by: Dakotakid on September 29, 2013, 10:09:39 pm

The one from ebay should be here in few days. Hopefully, it is a good one.
If not, will contact one of the above. Thanks.