VWDiesel.net The IDI, TDI, and mTDI source.
For Sale/Looking For => Parts for Sale/Wanted => Topic started by: tdotdub on September 16, 2013, 03:45:03 pm
-
sick of having sliping clutches! looking for a kit that will hold 120-140hp. message me what you have, links for new ones will help as well as I haven't been able to find any for sale for AAZ. I don't care for what flywheel it is 1 or 2 pin.
are 8v performance clutches the same as diesel ones? would those work? looking for suggestions.
-
So long as it is the right size disk, and as well as the right spline for your transmission. Yes, any mk1-2-3 8v clutch setup will work so long as they are also for the 020 transmission.
-
upgrade to an 02a and run a vr6 pp and tdi disc.
-
HP doesn't slip the clutch, torque does.
-
There is a big spline 020 clutch. I don't know but was thinking it came in the MK3.
I never had issue with my 210mm luk clutch for the aaz. I bought it for around 160.00 came with the throw out bearing, alignment tool, pp, and clutch. I didn't slip it in 10,000 miles probably had around 150hp in the old engine. Don't know how much torque.
Similar to this one...
http://www.ebay.com/itm/LuK-17-012-New-Clutch-Set-/400548294014?pt=Motors_Car_Truck_Parts_Accessories&fits=Make%3AVolkswagen&hash=item5d4289ed7e&vxp=mtr
-
I run an AAZ with a 16v 020 pressure plate/8v disc (210mm)/ 210mm gas flywheel and have had no problems.
-
I have an AHU in my mk1 with the 210 8v gas sachs setup. Flywheel, Pressure Plate and Clutch Disk.
I can slip it in 5th gear if I get on the power too aggressively.
-
upgrade to an 02a and run a vr6 pp and tdi disc.
so an AHU tranny? and has anyone else done that no issues?
I run a t3 turbo so boost comes on like a snail it slips only 3 gear and up and only sometimes...
-
I run an AAZ with a 16v 020 pressure plate/8v disc (210mm)/ 210mm gas flywheel and have had no problems.
where can I get this combo?
that's what I originally wanted but couldn't find it and ended up going with a local company that someone suggested and its complete crap what they made....
this one here>> id stay away, first time the fly wheel they gave was not machine properly, second time after well its still sliping...http://www.euro-drive.com/contact/default.asp
the spline on mine is a 24 tooth correct? how can I find out?
-
autohausaz.com (http://autohausaz.com)
order everything separately and you are golden.
-
upgrade to an 02a and run a vr6 pp and tdi disc.
Quoted for truth. And make sure it's a Sachs clutch, as the Luk kits hold a little less than the Sachs kits, which can hold as much as 290-300 ft-lbs of toruqe.
Also, what car is this for? The 5K? The beetle already has a 228mm clutch stock, and runs an 02J trans. The 5K is longitudinal, and I don't know what clutch diameter they use. Come to think of it, I don't know anything about 5ks or quantums.
-
upgrade to an 02a and run a vr6 pp and tdi disc.
Quoted for truth. And make sure it's a Sachs clutch, as the Luk kits hold a little less than the Sachs kits, which can hold as much as 290-300 ft-lbs of toruqe.
Also, what car is this for? The 5K? The beetle already has a 228mm clutch stock, and runs an 02J trans. The 5K is longitudinal, and I don't know what clutch diameter they use. Come to think of it, I don't know anything about 5ks or quantums.
I have read the luk kits are better by 10% and trust them fully. Sachs is what I replaced in my mkiv as it was slipping...
You could take my recommendation if you do not want to step up to the 02A. I have ran south bend, luk, clutchnet, and sachs. Sachs is the only brand I have slipped. For an OEM type clutch I fully recommend LUK. For a performance daily I recommend south bend, and for all out performance I recommend the clutchnet or a higher end southbend.
-
just figured out how to register so I did....was using a friends account tdotdub for my cabrio questions
I have a south bend in my alh and its a monster clutch, I only wish they had one for an aaz.
doing the 16v pp and gas flywheel sounds like the most budget friendly way, so thanks for the website link!
once I do that gotta install that 6.5td gm lift pump I bought, intercool it and call it a day :) the aaz potential is awesome.