VWDiesel.net The IDI, TDI, and mTDI source.

For Sale/Looking For => Parts for Sale/Wanted => Topic started by: theman53 on June 30, 2013, 06:02:16 pm

Title: I need 6 020 pressure plate to crank bolts
Post by: theman53 on June 30, 2013, 06:02:16 pm: I need these like right now. I have been looking for the past 3 hours for bolts that I cannot find. It is the only thing holding me up, otherwise I would bolt the trans on and it would be in the car. This is what I am looking for and I would need them to be found now and shipped first thing tomorrow, or I will buy this set and pay good for shipping so I get them by Wednesday.

http://techtonicstuning.com/main/index.php?main_page=product_info&products_id=330

(http://techtonicstuning.com/main/images/141.108.jpg)
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: CRSMP5 on June 30, 2013, 06:37:29 pm: all ya had to do was ask.. id have given ya bbob's out of his box..
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: theman53 on June 30, 2013, 06:46:28 pm: I have the old ones, but my manual says to replace and torque to 22+1/4
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: bbob203 on June 30, 2013, 07:19:34 pm: Ive reused them several times now on 020 and 02a with absolutely no issues just clean them and re loctite them.
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: theman53 on June 30, 2013, 07:32:41 pm: nah. usually any 1/4 deal the bolt deforms and I don't trust it.
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: bbob203 on June 30, 2013, 07:39:59 pm: If I was home id get you some and overnight them to you from the vw shop but I wont be home until wednesday.
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: theman53 on June 30, 2013, 08:04:58 pm: looks like I will call the FLAPS and then order from Tech up there. Tell them to send me them and pay the shipping for guaranteed no later than Wednesday. I will have it in the car by this weekend.
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: Dakotakid on June 30, 2013, 08:10:51 pm: This whole 22 plus 1/4 turn thing is sweet and everything.....

.....just make sure you end up at 74 ft. lbs.
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: CRSMP5 on June 30, 2013, 08:36:23 pm: i never have either.. i reuse and always have.. hell this vr6t are reused..
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: theman53 on June 30, 2013, 08:47:47 pm: I would but I have crazy mike's luck when it comes to this crap.
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: tyb525 on July 01, 2013, 04:29:52 pm: The Bentley for my '81 says 55lbs I think, nothing else. I think the older ones weren't TTY and were reusable.
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: theman53 on July 01, 2013, 09:28:32 pm: My issue is which ones did I have? I have had 3 aaz engines and a few 1.6L in the shed. I keep everything. Maybe some of mine were ok to reuse but I would rather be safe than sorry with this. I put some coin into the trans and engine so I don't want a failure because I skimped on a 2.00 bolt. My Bentley is mk2 and says x ft/lbs plus a quarter turn. Just scares me that is all.
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: Dakotakid on July 02, 2013, 06:38:44 am: Simple: wait for new bolts.

I've got 3 of the silver big Bentleys and NONE of them make any mention of 22 + 1/4.

What they do say is: 55 lb. for non-shoulders bolt, 74 lb. for shouldered.
I've always gone with the 74 lb. and no failures.

I thought we put this all to rest back when Damac performed his infamous driveway "flame-out."
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: theman53 on July 02, 2013, 06:55:38 am: yep, I will be waiting on new. they should be here tomorrow. I also have the jeep bolts now that are fully threaded m10-1.0x40 that I could cut down. They are socket heads instead of hex heads, but that shouldn't be an issue. I had to buy 100 of them from work but it only cost 32.00. cheaper than 6 from the wal mart of fasteners type stores so if I sell any jeep adapters I will be covered for about 16 swaps.
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: fatmobile on July 02, 2013, 10:02:17 pm: These bolts are something I go to the dealership for, not sure how fast they can get them.
I do reuse the old shoulderless ones.
Title: Re: I need 6 020 pressure plate to crank bolts
Post by: theman53 on July 03, 2013, 05:45:13 am: All the ones I have are full thread no shoulder. I have them coming. Dealer said they would be 5.xx each. I got them 2nd day air for less than that.