VWDiesel.net The IDI, TDI, and mTDI source.
General Information => Upgrades (non engine related ) => Topic started by: theman53 on May 31, 2010, 08:09:01 am
-
Just was looking at my oil lines again and got to thinking about vnt. I just wonder with all the axles and engine mount is a vnt possible in a mk2 jetta? Anyone tried it?
-
I heard that since it hangs really low it would hit the engine mount.
A euro vnt would have a better chance of fitting.
-
with a custom pass engine mount, a vnt would fit amazingly well. as they sit stock, the engine mount blocks over half of the turbo inlet.
-
I guess while I have it apart I should make one. Any pics of how this is possible/been there done it people? That italicized phrase is why this has taken 2 years plus to get this going >:(
-
What other options for a better turbo like VNT are there for MKII? I have that manifold still from AKI and next year want to upgrade to it and maybe a different turbo then:D
-
an integral manifold VNT needs a special rear engine mount. i havent drawn or fabbed one up yet, but im going to. on top where its straight, it needs to have a pretty good V built into it to clear the turbo inlet. other option is to use a big VNT on the other manifold you have.
-
I need to become a vendor, make, and sell the custom engine mount that the guy is asking over 200.00 for. Now that I see what it is I could make that with all the stuff I have. It doesn't look any different than the stock mount? check out the vendors section for what I mean.
http://www.vwdiesel.net/forum/index.php?topic=25902.0 (http://www.vwdiesel.net/forum/index.php?topic=25902.0)
-
Aren't there VNT17 flavors from Europe that did not have an integral manifold? Seems as though you might be able to make a simple adapter flange from the stock T3 manifold. The VNT15 is too small for the 1.6 anyway. :D
Brendan
-
VNT17 isnt too small tho, the one i got works GREAT on these smaller engines..
might be too small for you, but i had LOTS and LOTS of fun with my 17..
-
Yeah but he said 15 :D
Does someone have a VNT that they could measure how far from the head surface the intake starts and stops and...
How the intake of the VNT is in relation to the exhaust manifold studs.
I want to make a few brackets OR
Does someone have a trashed VNT they would let me use to make the bracket? I would take a good condition, but don't want to chance anything with someones baby.
-
the only problem is that the pass rear motor mount is where the cold side needs to go. if you built a custom motormount with a curve for the cold snail to sit in, it would work fine. its the damn pass side aluminum mount. i had an idea thought up in my head for a mount, if you want i could draw it up and scan it or take a pic or something? it would have worked too. a steel engine mount to fix the interference.
-
Yeah but he said 15 :D
Does someone have a VNT that they could measure how far from the head surface the intake starts and stops and...
How the intake of the VNT is in relation to the exhaust manifold studs.
I want to make a few brackets OR
Does someone have a trashed VNT they would let me use to make the bracket? I would take a good condition, but don't want to chance anything with someones baby.
With my euro vnt if you laid a ruler on the head gasket surface it would cross close to the center line of the compressor inlet. I can't remember the distance from the head to the center of the compressor inlet
-
but im assuming he already has a US spec VNT. and probably wants to put it on a mk2..
-
I don't have it yet, but I want it. If I get a VNT 17 I want to use it in the jetta MKII :D
-
its gonna be as hard as making an engine mount to clear the cold side and intake.
-
but im assuming he already has a US spec VNT. and probably wants to put it on a mk2..
Just comparing incase someone alse has those measurements.
-
could someone get me the measurements from the exhaust / intake surface on the head to the centerline of the VNT 17 and the relationship from the deck surface to how far up/down the centerline of the intake of the turbo? Not a bad run on sentence eh? Let me know if it makes sense to you...basically a vertical and horizontal measurements from a known location on the block to the center of the turbo inlet.
Wouldn't be bad to know the OD of the turbo inlet either :D
-
US or Euro spec VNT? i have a us spec vnt bolted to my 1.5 sitting on the floor...
-
US...I think I could get away with a euro as is. But parts for them are a pain from what I gather. The US 17 is what I eventually want to run. If you can let me know where the intake is in relation to the engine so I can repeat it that would be awesome.
-
Could you take a square to the oil pan up to the intake for that VNT. Let me know where the center is and I will be good. A picture from the TB side of the engine would be great to. Pretty square to the side of the engine too. I want to make this before I get the VNT so it will be and easier add:D