VWDiesel.net The IDI, TDI, and mTDI source.
Engine Specific Info and Questions => mTDI Mechanical TDI Conversions => Topic started by: dcg9381 on March 28, 2010, 07:30:18 am
-
I'm out of Austin, TX.
I've been lurking in your group for quite a while - registration apparently has been disabled until the site owner could patch up some site registration holes (due to spam).
I have a 1988 4runner that's in really good shape. A few years ago, I did a plug-and-play megasquirt (custom EFI project) integrating the stock harness with a megasquirt unit the could be plugged into factory wiring. Once I got that working, I converted it to a built turbo motor and have been driving it ever since.
The truck is up on www.22returbo.net (http://www.22returbo.net). We tuned it to run on gas or E85.
I largely retired the truck when gas went through the roof (it's get 15-18mpg on pump gas).
My interest now is pulling the turbo motor and converting it to TDI. I really need 130-150 hp out of a motor that powers it. After reading on this forum, I think what I'm after is a 2.0L TDI motor. The issue seems to be that you can't retain the factory direct injection due to fairly complicated anti-theft system.
I believe that both the 1.9L and 2.0L TDI motors can be bolted to my existing driveline via "acme adapters" in Canada.
I guess I'm looking for recommendations on a motor source - and a source for mechanical injection. Honestly, I'm not wanting to build it myself or adapt it, but don't mind paying for a high quality solution that works well. I understand that there are a few people / shops making MDI conversions, but some of those solutions don't have a very good record in terms of customer satisfaction...
-
I don't know if you have thought of the IDI line? I think a 1.5 with a turbo and some pump mods would do 130 to 150...I wouldn't choose that as your platform*Don't choose anything with 11mm head bolts*. I am just saying the TDI's are complicated and the older ones just need diesel, air, and 12v to the fuel seleniod.
Many have gone over the 200HP mark with the 1.6L TD. I think if I recall 180 HP with all stock parts IE turbo, rods, block, head, but a Giles pump is common. Maybe some may have put a 1.9 AAZ head to change some stock part to another stock part, but you get the idea.
I think you could build one of the IDI's to this and have about the same money as you will have in buying a TDI setup that needs redone. I don't know about much of the TDI stuff, other than it is too pricey for me to play with though ;). I am sure others will have some ideas for you as well. Good luck and welcome.
-
If I didn't already have a lead on an engine, I'd comb junk yards till I found a platform and go from there. It would probably mean building a head or redoing a bottom end -- or both, but it will likely still be cheaper than buying/shipping something complete.
There seems to be an absurd amount of markup in complete VW diesel engines in TX due to their rarity and desirability...
If you find a pre-1999 TDI you won't have to worry about the immobilizer. If you want to go mechanical TDI (mTDI), there's a ton of useful info on this forum as to what will or could work in place of the electronic fuel injection.
-
You could go with a 94 IDI 1.9 and a Giles pump and save a chunk of change. Passats are pretty much looked over and if you are near Texarkana you can visit neighbouring states and save a couple of bucks.
-
I'm open and thankful for suggestions.
What years had the 1.9L IDI?
My issue with buying on that old is that most will have pretty good mileage on them and probably require a rebuild instead of drop in...
If they're radically simpler, can do over 150hp reliably, and reliable - I'd certainly be willing to start in that direction...
-
You could get 150hp out of either the IDI 1.6td or 1.9TD. Drop in is a bit more difficult unless you find someone who has a hot engine built and sitting on a shelf. The 1.9td was a cananda only engine. It is available via some industrial applications here in the states. I guess a quetion would be what the truck is used for and what you have on it for running gear / driveline / tires. I have not checked out the build link yet. HP is kind of a odd term in the diesel world as a lower HP engine may have more TQ then a counterpart.
Best and easiest availability will probably be a 2003 or earlier tdi out of a wrecked car. You can do the whole ecu swap deal and run with a tuned ecu if you want. Another option that removes a bunch of the electronics and simplifies the process is to run a M-TDI. Mechanical control, ecu eliminated.
The most important part of a m-tdi swap is a correctly modified m-tdi pump. You run a pump that someone has hobbled together and you will never get the power you need. It will always be so-so.
Get a m-tdi pump from a reputable builder. They will build it to to compliment your driving style and needs.
Giles and tintin off the top of my head. I think baxter may build as well. Research the pump and builder more then the actual engine.
-
Best and easiest availability will probably be a 2003 or earlier tdi out of a wrecked car. You can do the whole ecu swap deal and run with a tuned ecu if you want. Another option that removes a bunch of the electronics and simplifies the process is to run a M-TDI. Mechanical control, ecu eliminated.
running an 03+ TDI on a custom ECU requires an expensive injection pump, correct?
I'd love to have a laptop programmable diesel ECU (similar to what I have now) - but don't want to have to retain anti-theft and integrate another wiring harness. If I could get it down to ECU + engine harness, that would be fine, however, I've seen the paired down wiring harnesses and honestly, it's not something that I care to learn or go through right now.
M-TDI is preferable to me for the above reason. I've seen commentary on the cobbled-together solutions and know to avoid them. I'll seek more information on the pump once I've decided on a motor. Advantages to the 2003+ TDI motors? What to look for? (I'm in the states)
Desired torque is in the 250 ft/lbs range.
31" tires. Rear axle is 4.10. Final drive (overdrive) is .850. I'm geared a little bit high for a diesel (3200 rpm at highway) - but this is easy to take care of. Replacing the entire driveline is not, which is why I like the acme adapter set.
Truck is mainly a pleasure / camping vehicle / project vehicle. Occasional light towing (1500 lbs or less). I'm after the torque, reliability, and mileage of the diesel application. Toyota does have drop-in diesels that can be imported, but reliability on the 2.0L variety isn't great, nor is part support in the USA.
Searching local yards (online) there seems to be a good selection of 1.9L motors, under 80k.. (01-03 Jetta, Golf, Beetle)
-
Get a 1.9L IDI put a good turbo on it and be done then ;)
-
I have lots of experience with turbos... :)
IDI would be great, but when I dig and try to find sources for the 1.9L IDI motor, I come up with:
'93-'98 GOLF/Jetta sold in Canada only
I'm about.. oh, 30 hours away from Canada..
The motors I can find in the states (easily) are 01-03 Jettas.. I assume are TDI. To use the TDI, I need the expensive mechanical conversion (M-TDI) - and what else? (Or keep the efi)
The TDI may be a better option for me, as I can get parts locally and won't have to import from the cold yonder north (Canada)...
-
yes you need the M-TDI pump and everything else that you would need for the regular IDI swap for the 01-03 TDI engines you are looking at.
The 1.9IDI is a Canada only item, but can be found in the for sale section here as well as ebay regularly.
The 1.6L IDI turbo diesel would do it too.
-
Thanks. I think I'll talk to giles - who seems to have the best record for mTDI conversions.
It's hard for me to wrap my head around going from a 2.4L gas/turbo motor to a 1.6L diesel and getting what I want out of it... I also need to consider parts availability.
-
http://www.vwdiesel.net/forum/index.php?topic=10690.120 (http://www.vwdiesel.net/forum/index.php?topic=10690.120)
Look at the very top and very bottom of this thread. It is documented as doable, but like everything it takes work.
I dont' know how readily available the TDI stuff is in your area, but around here it is big $$$ just to find one that needs redone. Good luck whichever way you go.
-
Thanks. I think I'll talk to giles - who seems to have the best record for mTDI conversions.
It's hard for me to wrap my head around going from a 2.4L gas/turbo motor to a 1.6L diesel and getting what I want out of it... I also need to consider parts availability.
haha yeah it is a big drop in displacement!!! ;D
Most parts for the 1.6 are everywhere, there's a few weird stuff that normally doesn't need replacing that are harder to get.
Another option is a 1.6 bottom end with a 1.9idi head, gives a lower CR so you can get fit more air into the engine.
The 1.9 (aaz) head will fit directly on a 1.6 with hydro lifters, a mechanical 1.6 takes more work but has been done.
IIRC you didn't want to build an engine though.........
-
running an 03+ TDI on a custom ECU requires an expensive injection pump, correct?
I'd love to have a laptop programmable diesel ECU (similar to what I have now) - but don't want to have to retain anti-theft and integrate another wiring harness. If I could get it down to ECU + engine harness, that would be fine, however, I've seen the paired down wiring harnesses and honestly, it's not something that I care to learn or go through right now.
If you swap over the ecu and harness, you are good to go with the injection pump that is on the engine. Tune till you are content. Perhaps a different turbo and or larger injectors, big downpipe with free flowing exhaust and you are good. How to get rid of the anti-theft crap is beyond me.
The m-tdi will be the easiest setup, but you will need to swap the pump, perhaps sell the ecu to help offset?
With IDI's ,If you are looking for TQ I would l lean more towards to 1.9td. Like mentioned above, they can be had in the states. Finding one that is a low mileage unit, in great shape, that is in drop in condition would be a bit of a challange. For complexity, they are way more simple then the TDI. Just older and harder to find.
-
I dont' know how readily available the TDI stuff is in your area, but around here it is big $$$ just to find one that needs redone. Good luck whichever way you go.
Just searching online there are a few in driving / pickup range, under 85k miles. Cost $2000 USD. I'd change the seals out, new timing belt, and call those motors done...
That little Rabbit did pretty good on the dyno... Still, better perhaps to start a little closer to that HP level to start with.
Is there a good way to adapt a T3 to a TDI motor?
-
I believe that both the 1.9L and 2.0L TDI motors can be bolted to my existing driveline via "acme adapters" in Canada.
Their plates work with any 22R Toyota transmission. When I spoke with them, they said it would work with MK3 engines of any kind for sure. They were unsure about MK4 and newer, but I believe the bolting pattern for the transmissions has not changed.
-
Look up aaz on ebay and you will find 1.9TD aaz's going for about $2200 shipped from CA. Decent low milage. I paid $2400 for mine with about 30k miles on it with a 5 speed.
As for putting in into your toy. I made the adaptor myself, and have all the prints for everything. I did a full adaptor that wraps all the way around the toy bell. Mine is mated together and going into a rock crawler.
Good info here..........
http://yotatech.com/f162/vw-diesel-build-up-135203/ (http://yotatech.com/f162/vw-diesel-build-up-135203/)
From what I've read the adaptor will work with a TDI (if I ever wreck my car I'll let you know 100%) I think the angle of the motor vs the trans might be different though. ???
-
Thanks. I can't find anything referencing AAZ on ebay currently - no motors, only pumps forsale.
Can anyone tell me what the AAZ designation is - and years that it applies?
There is a Jetta here (1998) - TDI - $1500. Owner says the pump is going bad making it hard to start. The bad news is that it's got 177k on it and I'd be tempted to rebuild it, which is going to run me at least another $1k... '
-
http://cgi.ebay.com/ebaymotors/VW-1900-Turbo-Diesel-Complete-Engine-AAZ_W0QQcmdZViewItemQQhashZitem439dc20ceeQQitemZ290409549038QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories (http://cgi.ebay.com/ebaymotors/VW-1900-Turbo-Diesel-Complete-Engine-AAZ_W0QQcmdZViewItemQQhashZitem439dc20ceeQQitemZ290409549038QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories)
Here is a link for a motor.
-
AAZ is a Canadian (and European) motor. In Canada it was used from 92 through 98. In 92 only Passats had them. Actually maybe it's 91.. I'm not positive.
-
Thanks for the link.. Somehow ebay doesn't like a straight "AAZ" search.
Motors look good, reasonable mileage.
stock 75hp and 115ft/lbs is a bit anemic... Maybe I should ask over on the IDI section, but what's reasonable power output on these things when keeping them reliable?
Is there a good T3 manifold available?
I found a local 98 Jetta with 177k - leaking some oil, pump is failing. TDI and complete for $1500 (entire vehicle) - I'd be tempted to rebuild it + cost of a M-TDI pump, we're probably looking at $4k.
-
If you can get the whole car why not just keep it straight up TDI? I would just see what is wrong with the pump, or if it even is the pump. I would have went with a TDI setup if I was able to find a donor car, But they want $5,000 for TDI's with over 200k around here.
-
yeah if you got the wiring and can get the whole car under 2,000 I would go TDI too...not mTDI full electric since the wiring is there like Mr. Woods said. I bet it isn't the pump.
-
Thanks for the link.. Somehow ebay doesn't like a straight "AAZ" search.
Motors look good, reasonable mileage.
stock 75hp and 115ft/lbs is a bit anemic... Maybe I should ask over on the IDI section, but what's reasonable power output on these things when keeping them reliable?
Is there a good T3 manifold available?
I found a local 98 Jetta with 177k - leaking some oil, pump is failing. TDI and complete for $1500 (entire vehicle) - I'd be tempted to rebuild it + cost of a M-TDI pump, we're probably looking at $4k.
That is pretty typical power for a TDI stock, the MK4s and newer are 150-200 ft lbs. For an MK4+ plan to spend more, but you can flash the ecu for increaded power. The AAZ can make good power with pump tuning, big injectors and other upgrades. If you are looking for power right out of the box you could pick up an NPR motor=)
-
You can chip tune ANY eTDI not just the MK4's.
75/115 is stock AAZ power, but easy to see the 120/200 range with pump mods & an intercooler. The stock injectors are fine for any tuning on an AAZ within reason. FIxing the crank nose isn't an option IMHO, check Libbybapa's profile for the fix.
North american TDI's in stock form 1Z/AHU - 89/149 (MK3 golf/jetta/b4 passat), ALH is 89/155 (mk4 golf/ jetta), AFN 109/173(B5.5 passat) ... i think that's all correct, there is some overlap here & there with the VW half model year changes.
Keep in mind that torque is available from around 2000rpm, so nice for a small truck.
Without a turbo upgrade I's say +20-30% can be found with just a chip tune on any of them, +40-60% tune and injectors & +100-infinity% with tune/injectors/turbo/clutch/...
180hp/300+ is pretty easy for ALH guys to see with a turbo/injectors/tune & then its clutch time, the 1Z's had slightly weaker pistons & maybe rods so aren't as popular for high HP builds.
This guy's got a nice 1Z/AHU build page http://www.stealthtdi.com/Jetta.html (http://www.stealthtdi.com/Jetta.html)
Those numbers are off the top of my head, i'm sure others can provide some tuned hp numbers here.
All of the TDI's in e form can run a VNT turbo, the 1z/ahu's need a ecu reflash to newer software for this tho & all benefit from a EGR delete or a upgraded CCV filter system to avoid clogged intake manifolds (something you should check on a used tdi purchase)
The other thing to watch with a used TDI engine is if its out of an auto or manual tranny car, auto's got a 11mm injection pump while the manuals got 10mm. Auto's had smaller injectors though while the manuals had larger injectors. That doesn't matter cause you're going to want some Bosio injectors anyway. Most tunes driven mildly will net better fuel economy too.
Pushing more than a small sedan a nice large intercooler and a upgraded oil cooler are a good idea. Many tuned tdi's run fuel coolers too.
There's a guy promising mtdi pumps from e pumps with a tiny mod, i'm taking that with a grain of salt until its proven.
ebay england always has land rover mTDI pumps, a simple mod to the IP bracket & its installed in a afternoon, I doubt the electronics could be figured in that time. Then you can tune with a screwdriver! Just don't discount the mTDI based off a few posts here, do some research if you're even just a little interested.
thats all i got, time for work...
-
ebay england always has land rover mTDI pumps, a simple mod to the IP bracket & its installed in a afternoon, I doubt the electronics could be figured in that time. Then you can tune with a screwdriver! Just don't discount the mTDI based off a few posts here, do some research if you're even just a little interested.
I don't count the mTDI out, but I have to budget for the only working mTDI pump that seems to have good references - which looks to be around $1300.
I'm just not interested in integrating the mTDI electronics. I'm capable of doing that, but simply don't care for the hassle, nor do I care for the expense of the tuning software and defeating the electronic anti-theft ($400?). It extends the learning curve and project length.
I like the references to the AAZ motor 120hp and 200ft/lbs is right no par with the 22RE gasser (stock). This would be a power reduction on my turbo motor... I really need to get to 150hp 200-250 ft/lbs. I do recognize that those power peaks are pretty early on a diesel - maybe 1500 rpm sooner than the stock gasser and mileage would be significantly improved.
I have a newer T3 that I'm running currently - a .48/.60 - I'd like to put that on whatever motor I choose to run with.
I'm also already intercooled.
I appreciate the commentary and contributions here - this is a great forum.
-
For reference to the discussion & comparison:
22RE('85-95):
bore - 92mm
stroke - 89mm
compression ratio - 9.4:1
116hp @ 4800rpm
140tq @ 2800rpm
-
Thanks, I didn't realize they were that anemic stock, although the peak torque is similar to a diesel.
The turbos do a lot better, I have a collection of dynos at:
http://lakebox.dnsalias.com/photos/1988%204runner/engine/dyno/ (http://lakebox.dnsalias.com/photos/1988%204runner/engine/dyno/)
-
That t3 is bigger than what came stock on the 1.6ltd. You could use it but turbo lag would be significant in a heavier vehicle. The 1998 jetta probably has a garrett t2 or the kkk equivilant which will work much better in your application. I'm running a k14 on my mtdi right now in my toyota pickup and it's nice. Spools up fairly quick and I'm making full boost, 18 psi, from 2000-3800 rpm.
It is possible to make more power than your turbo 22re but it will take some upgrades like larger nozzles, a better intake, porting the head,a vnt turbo, and a very well built mtdi pump. The tdi does feel really torquey though, with good low rpm grunt.
So, personally, the only reason I would ever do another swap like this is if I wanted to. It doesn't make sense to do this for any other reason. My final cost was over 5g for the conversion and that doesn't include my time. Yes I'm getting better fuel economy but I'm only saving about 10 bucks a week so at current fuel prices it's going to take ten years for the payback!
I also notice extra weight in the truck more than before. I notice a big difference in acceleration and power. You might find this hard to believe but I fill the fuel tank and I feel the difference. I hall two passengers and I feel a big difference.