VWDiesel.net The IDI, TDI, and mTDI source.

For Sale/Looking For => Parts for Sale/Wanted => Topic started by: houseofdiesel on February 23, 2009, 03:34:59 pm

Title: FS CTN transmission (02A mk3 tdi)
Post by: houseofdiesel on February 23, 2009, 03:34:59 pm: I have another CTN code 02A transmission, out of a 1996 Passat tdi, no cables or hydraulics included just the trans. $400. These make a great swap into older models, 95km/h is 2000rpm (59mph) great gearing. willing to ship or deliver in Toronto/Montreal corridor at cost.
Greg
Title: Re: FS CTN transmission (02A mk3 tdi)
Post by: gnavs on May 28, 2009, 01:21:22 pm: is this a cable clutch tranny?
edit: nevermind, i don't think 02A's were cable
Title: Re: FS CTN transmission (02A mk3 tdi)
Post by: jtanguay on May 28, 2009, 03:56:09 pm: Quote from: gnavs on May 28, 2009, 01:21:22 pm
is this a cable clutch tranny?
edit: nevermind, i don't think 02A's were cable

unfortunately... although i do believe some 02A's in Europe had the cable clutch... i found a kit to convert the tranny for about $400USD. :o

my idea is to create a linkage to use the cable to actuate the master cylinder... thereby bypassing everything. it'll surely make bleeding the clutch a lot easier too! (i think? :-[) all i need to do is make sure there is enough travel in the cable to fully actuate the MC, then its go time. the linkage shouldn't be difficult at all to create either. particular attention must be paid to the angle of the rod though... as to try and keep it as linear as possible to reduce the amount of wear.

this is a really good price for this transmission! CTN = smileage ;) i'd also recommend switching to something like lubro moly gear lube to further reduce friction.
Title: Re: FS CTN transmission (02A mk3 tdi)
Post by: aidan on May 29, 2009, 07:54:07 am: jtanguay, your idea already exists, it came on the early seat tdi's.

You still have to swap the shifter box and cables in though
Title: Re: FS CTN transmission (02A mk3 tdi)
Post by: jtanguay on May 30, 2009, 12:51:48 pm: Quote from: aidan on May 29, 2009, 07:54:07 am
jtanguay, your idea already exists, it came on the early seat tdi's.

You still have to swap the shifter box and cables in though

hmmm i've heard of those cars having cable shift, but i never thought that they would do something as crazy as cable operated hydraulic clutch? weird... not saving $$$ there ;D but yes i have the shifter box & cables as well, although the one from a 1.6/1.9 can be swapped into the transmission for a rod shift conversion ;)
Title: Re: FS CTN transmission (02A mk3 tdi)
Post by: aidan on May 31, 2009, 12:47:25 pm: http://www.clubgti.com/forum/showthread.php?t=107068 (http://www.clubgti.com/forum/showthread.php?t=107068)

Hard to explain, and never done it myself, but as far as I gather it just converts the 'pull' from the cable to the 'push' normally given by hydraulic
Title: Re: FS CTN transmission (02A mk3 tdi)
Post by: jtanguay on May 31, 2009, 05:04:10 pm: Quote from: aidan on May 31, 2009, 12:47:25 pm
http://www.clubgti.com/forum/showthread.php?t=107068 (http://www.clubgti.com/forum/showthread.php?t=107068)

Hard to explain, and never done it myself, but as far as I gather it just converts the 'pull' from the cable to the 'push' normally given by hydraulic

that looks like it does away with the hydraulics though...
Title: Re: FS CTN transmission (02A mk3 tdi)
Post by: lord_verminaard on June 01, 2009, 08:50:10 am: I got the same rig for my TDI swap, 02J in a Scirocco. It's all factory stuff. The cable is very similar to the manual-adjust clutch cables in A1 and A2 cars. All it is is a lever that pushes in on the clutch fork in the bellhousing.

I think this setup was also used on some Eurovans (in Europe) that had 02A transmissions. I bought the whole setup (brackets, lever, cable, etc...) from a chap on here for very cheap.

Brendan