VWDiesel.net The IDI, TDI, and mTDI source.

Engine Specific Info and Questions => IDI Engine => Topic started by: the caveman on September 30, 2008, 07:59:12 am

Title: ID pump head size by part # ?
Post by: the caveman on September 30, 2008, 07:59:12 am

I'm working my way backwards trying to find out what size the head was on the 1Y 1.9 na motors. The bosch numbers based on the information i got from vagcat are : 028 130 115 PX and QX , 068 198 015A, 068 130 081 JX and 028 130 107 KX I just want to know if they are 9mm or 10mm

Title: ID pump head size by part # ?
Post by: Turbinepowered on September 30, 2008, 04:35:21 pm

Is it a pump you have in your hands? I don't know VW part numbers, but I can give you the full layout for Bosch part numbers.

Title: ID pump head size by part # ?
Post by: the caveman on September 30, 2008, 08:20:54 pm

No i don't have them in my hands. I was hoping that they be cross referenced.  basically i'm trying to determine what size head would have been on a 1Y 1.9 NA.

Title: ID pump head size by part # ?
Post by: blkboostedtruck on September 30, 2008, 09:00:42 pm

i'll take an educated guess? 9mm let me know if i'm right?

this make's my 1000 post lets have a party
Duane :twisted:

Title: ID pump head size by part # ?
Post by: burn_your_money on October 01, 2008, 04:55:37 am

I have a 028 130 107 Q 1.9 NA pump and it is a 8mm. Hope this helps.

I'm moving this to the IDI section as well

Title: ID pump head size by part # ?
Post by: madmatt on October 01, 2008, 06:28:28 am

should be 8mm on a 1y

Title: ID pump head size by part # ?
Post by: zukgod1 on October 01, 2008, 07:03:23 am

Quote from: "blkboostedtruck"

this make's my 1000 post lets have a party
Duane :twisted:

1000 posts!?

Hooray!!

Wheres the keg?

Title: ID pump head size by part # ?
Post by: the caveman on October 01, 2008, 07:11:42 am

Quote from: "zukgod1"

Quote from: "blkboostedtruck"

this make's my 1000 post lets have a party
Duane :twisted:

1000 posts!?

Hooray!!

Wheres the keg?

woo-hoo [chug,chug,chug]

Title: ID pump head size by part # ?
Post by: the caveman on October 01, 2008, 07:15:04 am

I'm hoping it was 9mm. I just had a 10mm put on and i'm gonna drop into my transporter this friday/saturday. I just hope it gets me to the power level i need so i can then change my R&P from a 5.5 [!] to the 4.86 i got sitting in a box. Thanks everyone, at least its encouraging.

Title: ID pump head size by part # ?
Post by: madmatt on October 01, 2008, 02:59:04 pm

make sure you let the engine breath and dont bother with the small 16na exhaust.If the engine is at 50degs then i use an audi80 gas manifold an a2" exhaust.My old pick would wheel spin in second first was of no use with the5.5 r&p and it was flat out at an indicated 80mph a 5 speed 3h box out of a jx bus ment i could change into top at 70mph