VWDiesel.net The IDI, TDI, and mTDI source.

General Information => Troubleshooting => Topic started by: mtnbob on October 30, 2007, 12:34:06 pm

Title: Cylinder Walls had some grooves Mech honed out Is that ok??
Post by: mtnbob on October 30, 2007, 12:34:06 pm

Ok mechanic is deep into my engine, since i was getting blowby. Said that there were marks in the cylinder walls on two of the cylinders walls. not deep grooves but you could see them. He honed all of them out and said that i can either run it with new rings or bore it out and put in oversize pistons and rings. Not sure which way to go. I also remember hearing about rings on here that were supposed to be more expensive but sealed better. Any suggestions??  
   
The standard rings that he ordered will be there tommorrow so I have a day to make a decision. I plan to keep the car so I'm not trying to patch it up, but my budget is getting tight on this car too.

Title: Cylinder Walls had some grooves Mech honed out Is that ok??
Post by: rallydiesel on October 30, 2007, 01:49:51 pm

This guy sells cylinder liners for our cars:

http://www.dieselvw.com/16DieseLiner.htm

Title: Cylinder Walls had some grooves Mech honed out Is that ok??
Post by: mtnbob on October 30, 2007, 02:41:59 pm

I just ordered goetz rings from myke_w 8)

Title: Cylinder Walls had some grooves Mech honed out Is that ok??
Post by: saurkraut on October 31, 2007, 05:39:00 am

Quote from: "rallydiesel"

This guy sells cylinder liners for our cars:

http://www.dieselvw.com/16DieseLiner.htm

I wonder if they make a big enough sleeve to run the 1.7 pistons?  Probably end up being a wet sleeve.

Title: Cylinder Walls had some grooves Mech honed out Is that ok??
Post by: jimfoo on October 31, 2007, 08:47:53 am

Quote from: "rallydiesel"

This guy sells cylinder liners for our cars:

http://www.dieselvw.com/16DieseLiner.htm

I like this line from his site about rebuilt IPs.
"The pic is only a sample pic. I normally don’t clean the outside of my pumps."
That is sure a confidence builder about the build quality.

 :shock:

Title: Cylinder Walls had some grooves Mech honed out Is that ok??
Post by: rallydiesel on October 31, 2007, 09:34:55 am

Quote

I like this line from his site about rebuilt IPs.
"The pic is only a sample pic. I normally don’t clean the outside of my pumps."
That is sure a confidence builder about the build quality.

lol, I thought that too. I wouldn't buy a rebuilt pump from him but I've bought many parts and his prices are great.

Title: Cylinder Walls had some grooves Mech honed out Is that ok??
Post by: duffer on November 02, 2007, 12:04:04 am

Quote from: "rallydiesel"

Quote

I like this line from his site about rebuilt IPs.
"The pic is only a sample pic. I normally don’t clean the outside of my pumps."
That is sure a confidence builder about the build quality.

lol, I thought that too. I wouldn't buy a rebuilt pump from him but I've bought many parts and his prices are great.

His prices are great?
His prices are astonishing!
Where's his stuff made...China?

Title: Cylinder Walls had some grooves Mech honed out Is that ok??
Post by: zukgod1 on November 02, 2007, 10:36:16 am

Quote from: "duffer"

Quote from: "rallydiesel"

Quote

I like this line from his site about rebuilt IPs.
"The pic is only a sample pic. I normally don’t clean the outside of my pumps."
That is sure a confidence builder about the build quality.

lol, I thought that too. I wouldn't buy a rebuilt pump from him but I've bought many parts and his prices are great.

His prices are great?
His prices are astonishing!
Where's his stuff made...China?

I think some of it is China made but I do know he gets allot of his stuf from Germany also so.....

Title: Cylinder Walls had some grooves Mech honed out Is that ok??
Post by: addautomotive on November 07, 2007, 06:57:40 am

set of 4 pistons (.5 or 1mm oversize) for $189??

AAZ head (NEW)for $279???

Title: Cylinder Walls had some grooves Mech honed out Is that ok??
Post by: Gearhead on November 07, 2007, 09:40:25 am

He's even supposed to be putting together 1.6M-TDI kits for people that want the efficiency and power of a TDI but have a 1.6.  Hrmm...

Title: Cylinder Walls had some grooves Mech honed out Is that ok??
Post by: rallydiesel on November 07, 2007, 09:49:53 am

Quote

He's even supposed to be putting together 1.6M-TDI kits for people that want the efficiency and power of a TDI but have a 1.6. Hrmm...

For under $1000  :shock: