VWDiesel.net The IDI, TDI, and mTDI source.

Engine Specific Info and Questions => TDI Engine -General Info => Topic started by: A2TD on September 27, 2007, 06:30:28 am

Title: Yesterday my TDI hit the rollers and........................
Post by: A2TD on September 27, 2007, 06:30:28 am

(http://traxtermaster.homeip.net/~matt/photos_06a3a652/mydyno.jpg)

No chips and dip.........................

Title: Yesterday my TDI hit the rollers and........................
Post by: OM617 on September 28, 2007, 07:19:33 am

Its difficult to see the numbers because of the light ink, what are they?

Title: Yesterday my TDI hit the rollers and........................
Post by: jtanguay on September 28, 2007, 09:03:58 am

277 ft/lbs torque max and almost 184 hp max.

pretty impressive if there is no chipping... but how would you attain that without chipping??? must be bigger nozzles for sure..

Title: Yesterday my TDI hit the rollers and........................
Post by: A2TD on September 28, 2007, 10:05:18 am

184whp 278lbs, on the stock chips, all the timing and fuel was done with a hand full of resistors.................

I have a video I will post up shortly..

Title: Yesterday my TDI hit the rollers and........................
Post by: zaprzal on September 28, 2007, 10:09:10 am

what is your setup?

Title: Yesterday my TDI hit the rollers and........................
Post by: jtanguay on September 28, 2007, 11:13:45 am

with a hand full of resistors?  :lol: pretty neat! sounds like a hillfolk mod...

Title: Yesterday my TDI hit the rollers and........................
Post by: Holeshot on October 04, 2007, 10:32:05 am

Please do detail the values and placement of said resistors.  :twisted:

I'm running a 670-Ohm resistor (switched) between the #2 and #3 wires of the IP harness - aka: "Evry" mod.

I also have a resistor on the fuel temp wire, but that didn't seem to do much of anything.

Thanks,

Matt

Title: Yesterday my TDI hit the rollers and........................
Post by: Holeshot on October 18, 2007, 09:49:07 am

Quote from: "A2TD"

184whp 278lbs, on the stock chips, all the timing and fuel was done with a hand full of resistors.................

I have a video I will post up shortly..

How 'bout that video and some more details on the resistors...  8)

Thanks,

Matt

Title: Yesterday my TDI hit the rollers and........................
Post by: A2TD on October 29, 2007, 09:19:38 am

Quote from: "Holeshot"

Quote from: "A2TD"

184whp 278lbs, on the stock chips, all the timing and fuel was done with a hand full of resistors.................

I have a video I will post up shortly..

How 'bout that video and some more details on the resistors...  8)

Thanks,

Matt

Workin on getting the video working, its on an olderskool camera so transfering it over to the comp isn't easy.

Title: Yesterday my TDI hit the rollers and........................
Post by: jtanguay on October 29, 2007, 09:16:30 pm

you've essentially doubled the HP and more than doubled the torque of the stock engine... WITH RESISTORS!!!

i can't wait to see a video of this!  8)

Title: Yesterday my TDI hit the rollers and........................
Post by: Holeshot on November 08, 2007, 10:57:39 am

Still waiting...  :)

In the meantime while you're getting the video prepped - hows about posting information on the placement and values of them there resistors?   8)

Beers,

Matt