Fixmyvw.com

Recent Posts

Pages: [1] 2 3 4 5 ... 10
1
IDI Engine / Re: Sharing my 1.6td project
« Last post by as4k on May 06, 2024, 10:13:30 pm »
Maybe just check the battery terminals and the ground to the frame.  If the Alt is putting out the right amount of power then maybe it just isn't getting in to be stored as it should.

Ah, interesting thought.  So, where should the engine to body grounds be?  Honestly the only ground I can think of is the battery negative to the transmission bolt.  Since I got this car with pretty much nothing assembled I didnt even think about additional grounds. 
2
IDI Engine / Re: Sharing my 1.6td project
« Last post by ORCoaster on May 06, 2024, 09:41:45 pm »
Maybe just check the battery terminals and the ground to the frame.  If the Alt is putting out the right amount of power then maybe it just isn't getting in to be stored as it should. 
3
IDI Engine / Re: Sharing my 1.6td project
« Last post by as4k on May 06, 2024, 08:43:31 pm »
Sounds like you have a nice setup.
 Check to see if the alternator is putting out.
Cuz it probably should have charged the battery enough while running.

And as usual I forget some useful information :D.  I'll check again for sure.  The volt meter inside the car showed like it had good voltage but I'll check it at the battery.  Alternator is fairly new, not that it matters. 

Yes, the more space is outstanding.  I was doing rear brakes on my other Audi a few days ago and was in the driveway.  I had so much space and nobody around to watch me!  Def enjoying this so far and cannot wait to get the garage all sorted so we can fit some cars in there :)
4
IDI Engine / Re: Sharing my 1.6td project
« Last post by fatmobile on May 06, 2024, 05:39:03 pm »
Sounds like you have a nice setup.
 Check to see if the alternator is putting out.
Cuz it probably should have charged the battery enough while running.
5
IDI Engine / Re: Sharing my 1.6td project
« Last post by as4k on May 05, 2024, 11:15:40 pm »
Been a minute so I'll provide a small update.

We are now moved into our new house.  Both of my Audi's were actually the first things moved over, so that was nice.  The 4ktd was towed and I drove my other one.  We now have just a bit over 2 acres of land, a much larger attached garage, and room/plans to build a separate out building, so TONS of room for activities.
For the first time under my ownership and likely many years, the 4ktd sits outside, and doesnt look too shabby out there.  i hopped in the car last week after charging the battery in hopes to see if it would start and run.  A few cranks and a bit of help from the go pedal and it came to life.  I still have the odd surging idle, but it may just be the idle still needs adjusted up some.  Runs great though.
I made a few notes the last time the car ran.  Fuel leak from injector #4 where the rubber cap sits over the last port on top of the injector.  I cant tell if the actual nipple there is a bit tweaked or the cap just needs a small zip tie.  Either way I have another injector to toss in.  I need to tighten the turbo oil feed line a bit.  The clutch pedal wasnt returning all the way (but it is now), and the brake pedal is still hard.  So this means the vacuum pump may not have fixed the hard brake pedal issue.  I said screw it and ordered a new master and brake booster.  I hope to get this stuff replaced yet this month.  The only other oddity was that after letting the car run until the main cooling fan came on, I shut it down, then immediately tried to restart.  I got a very slow crank and no start.  I suspect the battery, which isnt 2 years old (but had a 2020 date on it) is toast.  I've done enough charging and jumping with it :)

I do owe you guys some updated photos and a video of it starting/running.  I also did acquire the correct crank bolt, so I'll take time to replace that.  I was really hoping to take this thing to Carlisle (which is this week) but moving sidelined ALL car related activities. 
6
Parts for Sale/Wanted / Re: Valve cover cup washers
« Last post by Dennis Froelich on May 04, 2024, 08:12:06 am »
Looks like Cascade German has them and Rockauto shows them.
7
Parts for Sale/Wanted / Valve cover cup washers
« Last post by mammonista on May 04, 2024, 12:46:14 am »
Hi all,
Desperately need three of the steel cup washers that go above the large, rubber valve cover grommets on my 1z TDI motor. Anyone have any? Or a source for new?
8
Early MK2s had 2 plugs on the cluster, later, CE2 clusters used one plug.

 I think I have plenty of relays for now, but appreciate the offer and I hope you find a good home for them,
find someone that needs them.
 I'm not actually sure what a MK4 MAP sensor plug looks like. Still learning the MK4 TDIs.
When I find out I'll look through the pictures again.
9
I am wondering if any of those plugs will fit the MK2 gauge cluster.  Then it could be wired to the MK1 version and be that much nicer of an upgrade mod.

Any idea? 
10
Local mechanic retiring, guy threw out very little. He was a VW mech in Europe but didn't like it here so he puts a full hoist in his garage and does cash jobs through word mouth for 2 decades, accumulates spares. I got a few stacks of belts from him, some early body parts, couple of pumps.. he worked on diesels primarily.

He drives Toyotas now.

Fatmobile if you see anything in the photos you want lmk.
Pages: [1] 2 3 4 5 ... 10
Fixmyvw.com