-
#30 by libbydiesel on 23 Oct, 2020 14:05
-
New Luk flywheel would probably be fine also.
-
#31 by monst on 23 Oct, 2020 22:44
-
GTK..... Thanks!....
I may go that route.......
In the event I do......... What I saw for "compatibility".....
It said,,,,,,,,(requirements being)
Single Alignment Dowel Pin 7.4x1.75mm -
Also Use 027 198 141E Clutch Kit Or 027 141 026C Plate; Engine: VIN: K; Transmission: Manualless
Single Alignment Dowel Pin 7.4x1.75mm -
Also Use 027 198 141E Clutch Kit Or 027 141 026C Plate; Engine: VIN: A; Transmission: Manualless
(have to research the kit #.... and why it makes that suggestion....)))
Just wondering If anyone knows Engine: VIN K
AND Engine VIN A
What bit position are they lookin at for VIN K and VIN A......
I don't have my VIN in front of me....... I guess... perhaps I might be able to deduce... something if I did....
VIN K and VIN A ... (dont' have anythin to do with the plant which the wheels were manufactured??))
I will have to look deeper if I am to purchase a new one..........
(ebay ones are cheaper but, I believe are without the dowel pins)
The pins on ebay are rather expensive..............
Is it ok to reuse dowel pins?
When the old one gets resurfaced.........
what is the idea there?
reuse pins........ install new pins? thanks......
MOnst
-
#32 by libbydiesel on 24 Oct, 2020 04:10
-
I don't know about the VIN values.
It is fine to reuse the dowel pins. -
#33 by monst on 24 Oct, 2020 21:58
-
Gtk thanks....
I got another place to go with it on Mon....
Seems to think he can cut it..... He has been in the bus... for long time...
So I will see what his vibe is..........
And explain.... dowel pins are to be removed.... both surfaces are to be machined.....
Monst
-
#34 by fatmobile on 25 Oct, 2020 00:08
-
Yeah, the dowels come out pretty easy with vice grips
tap right back in.
LUK is good quality.
Not sure I'd name my auto parts company LUK ,...
or FAG for that matter, ha. -
#35 by monst on 26 Oct, 2020 21:41
-
GTK...
Yeah, dropped it off somewhere... he will look at it and let me know a price tomorrow...
If it is ridiculous.... Those Luk's... where like 60 bucks......
I will just do that....
(yeah have to watch out when choosing an Acronym as the name of your company
)
(Luk...... to close to Puke...)
I have to start collecting all my new parts........
Do you know where to get the best prices online....
I guess that is where I will get my stuff...... or at least use that as my reference... and buy local........
STUFF
- Clutch kit
- rear seal
- input seal
- shifter seal
- transaxle drive flange seals
- trans axle mount (hydraulic -- mine is fried)
- valve cover gasket....
- CAN YOU THINK OF ANYTHING ELSE??? WHAT MIGHT I BE MISSING???
If you can make recommendations much appreciated.....
hypertext links are cool! to the items.... if possible
or part numbers..............
Also yeah,, I want to re-pack the inner cv joints......
To what detail (should/ can I get away with)... doing this.......
THanks, MOnst
-
#36 by lovevws on 26 Oct, 2020 22:37
-
Make sure you center the clutch disc.
If you dont have the centering tool.
You can use vernier calipers to center it. Or something like that to center it.
Then tighten the flywheel to the pressure plate, have it just snug enough that you can move the disc around a bit. -
#37 by fatmobile on 29 Oct, 2020 01:03
-
Runnin on LUK, ha.
Most people don't think to center the disc the push rod presses against.
I run a bic pen around the outside.
In the space between the disc and pressure plate.
Parts places for the 1.6 stuff.
Lately I've been using rock auto or autohaus.
Or the local NAPA.
Sometime oreilly. -
#38 by monst on 31 Oct, 2020 01:23
-
GTK, Thanks!
Yeah, Bought somewhere else...
Sorta got strung along..... That is when I just came out and said... Will it be more than a Franklin to cut the flywheel?
I even told him that the guy with a jig set up specifically for that flywheel wanted 150. His eyes lit up when I said I can get a new one for 60 samolians.......
Anyway, I have to collect parts still, been sidetracked with other crazy projects........
Can anyone chime in the list above regarding parts?
thanks, Monst -
#39 by libbydiesel on 31 Oct, 2020 19:19
-
- Clutch kit
- rear seal
- input seal
- shifter seal
- transaxle drive flange seals
- trans axle mount (hydraulic -- mine is fried)
- valve cover gasket....
- CAN YOU THINK OF ANYTHING ELSE??? WHAT MIGHT I BE MISSING???
Push rod bushing: 020311107C
Push rod seal: 020311108A
Clutch kit: Sachs K0028-03 (that's the last one I got for my '79 rabbit - I believe it would be the same for you but confirm before ordering)
Trans end cap: 020141073A
Pressure plate to Crank bolts: N90206103 -
#40 by fatmobile on 31 Oct, 2020 20:41
-
A '79 Rabbit might have the 180mm clutch instead of the 200mm behind the later 1.6D.
-
#41 by monst on 03 Nov, 2020 23:32
-
Thanks!
Be ordering stuff sometime this week....
Buying a new FlyWheel I will....... Second place didn't work out.....
Vin: K and Vin:A might have to do with the 8 digit....
which is this.....
4th – 8th Character – The next five characters tell you all about vehicle itself. The characters vary between automakers, but for the most part, the letters and numbers include information about the body style, engine type, model, series and more.
I am wondering
I ran a compatibility check for the flywheel below is what the results are.....
Josephina is a 1991 Vw Diesel jetta 1.6l naturally aspirated...
RESULTS:::::::::::
Compatibility
To confirm that this part fits your vehicle, please choose a vehicle from the "My Garage" list OR enter your vehicle’s details below.
My Garage
Select a vehicle
Go to My Garage
or
Year Make Model Trim Engine
1991
Volkswagen
Jetta
GL Sedan 4-Door
1.6L 1588CC 97Cu. In. l4 DIESEL Naturally Aspirated
[show all compatible vehicles]
This part is compatible with 2 vehicle(s) matching 1991 Volkswagen Jetta GL Sedan 4-Door 1.6L 1588CC 97Cu. In. l4 DIESEL Naturally Aspirated.
Notes
Important part details Year Make Model Trim Engine
--------------------------------------------------------
***Single Alignment Dowel Pin 7.4x1.75mm - Also Use 027 198 141E Clutch Kit Or 027 141 026C Plate; Engine: VIN: A; Transmission: Manualless 1991
Volkswagen Jetta GL Sedan 4-Door 1.6L 1588CC 97Cu. In. l4 DIESEL Naturally Aspirated
---------------------------------------------------------------------------------------------------------------
***Single Alignment Dowel Pin 7.4x1.75mm - Also Use 027 198 1...more 1991 Volkswagen Jetta GL Sedan 4-Door 1.6L 1588CC 97Cu. In. l4 DIESEL Naturally Aspirated
--------------------------------------------------------------------
Portions of the information contained in this table have been provided by autopartsgeek (they are the seller... listing is E bay)
Item specifics
Condition: New Brand: LUK
Application: Volkswagen Jetta Flywheel Part Number: 76524KT
Product Name: Flywheel Warranty: 12 Month Warranty
CS-SKU: 400:76524KT Years: 1997 1996 1986 1983 1984 1985 1987 1988 1989 1990 1991 1992 1993
What do you think.....
I could call partsgeek? do they pick up phones?
thanks, MOnst
-
#42 by fatmobile on 04 Nov, 2020 00:46
-
I don't know the part numbers.
Just 200mm and the smaller center splines than the 16V trany mainshaft used. -
#43 by monst on 22 Nov, 2020 00:27
-
Thanks!...
Yeah, my time(which is spread of many many catastrophes all the time)
just passes by this set of wheels up on jack stands in the garage......
Soon I will delve back in......
So I measure the clutch.... as you are saying 200mm & smaller splines......