M-TDI Pump - TDI Engine -General Info - VWDiesel.net The IDI, TDI, and mTDI source.

• M-TDI Pump by GEE-BEE on 06 May, 2014 19:15
• I spoke with Giles today and i was informed that I need to send three pumps to build a 11mm M-TDI pump
  
  AHU
  1.9 AAZ
  1.6
  
  After the purchasing two cores/frht  or purchasing a Rover Pump I will just buy a new 12mm assy
  
  http://advancedautomotion.com/shop/product_info.php/cPath/49_118/products_id/109
  
  Done, moving on to new turbo and manifold purchase..
  
  I think the motor is going to cost more than the Caddy...
  
  New rods
  stage 2 cam
  Oversize new pistons
  Fuel injectors
  
   
  
  GB
• #1 by theman53 on 06 May, 2014 19:59
• That is awesome that you are doing this for him.
  
  When you get the rods, please let me and all of us know what you go with and why. I really like the looks of the x beam and want them for the jeep, but I cannot justify the coin right now.
• #2 by GEE-BEE on 06 May, 2014 21:10
• Colt
  http://www.kermatdi.com/servlet/the-8302/camshaft/Detail
  
  
  Nozzles
  
  http://www.kermatdi.com/servlet/the-608/bosio-ulsd-1019%2C-nozzles%2C/Detail
  
  
  Pistons
  http://www.kermatdi.com/servlet/the-8354/Performance%2C-Internals/Detail
  
  
  Greaseworks is doing the build for me as he has been very good customer for years on my silicone Vanagon hose kits
  
  Will see what he chooses for the rods, there is some headwork that will happen
  Iam looking for 175 to 230 hp, great for a 1900 lb caddy
  
  GB
  
  
• #3 by vanbcguy on 06 May, 2014 21:54
• I like my Integrated Engineering rods. They fit the AHU block without interfering with the IM shaft, something you can't say for most of the aftermarket options.
  
  Sent from my HTC One XL using Tapatalk
• #4 by sdubfid on 06 May, 2014 22:00
• Not a bad way to spend 10,000 dollars
• #5 by vanbcguy on 06 May, 2014 22:26
• Don't I know it........
  
  Sent from my HTC One XL using Tapatalk
• #6 by theman53 on 07 May, 2014 04:49
• Red Rotors here has nozzles that may be better for you. Check the for sale section sticky and see if the cost vs what you get isn't better for your goals...all while supporting the owner of the site
• #7 by vanbcguy on 07 May, 2014 05:57
• I've got his nozzles in Jezebel... Though Marc was out of stock so I had to buy them elsewhere.
  
  http://www.hflox.com/di_nozzles_car.htm
  
  I have the Warp-7 nozzles.  They are a tad larger than the Race-520s you see elsewhere.
  
• #8 by vanbcguy on 07 May, 2014 07:53
• Also worth mentioning - the Kerma nozzles you list above are not really suitable for the power goals you have.  While they technically can get up to 190 HP with their "Stage V" treatment (which as far as we've been able to discern is done by raising the pop pressure quite a bit) the injection duration is going to be quite long at that point.  The result will be higher EGTs and more smoke than if you had a larger nozzle which could inject the same amount of fuel over a shorter duration.
• #9 by GEE-BEE on 07 May, 2014 08:21
• The nozzles will be sent in a matched...
  
  There on the list, but not purchased
  
  Pump is next, I found new hard lines and a new engine cover
  
  I have to match all the ext bolts with the arp 12point s/s lange type..
  
  Thanx